Differences
This shows you the differences between two versions of the page.
Next revision Both sides next revision | |||
techtalk:ref:carb01j [2019/09/08 21:29] hippysmack created |
techtalk:ref:carb01j [2019/09/10 00:26] hippysmack [Throttle Cable] |
||
---|---|---|---|
Line 124: | Line 124: | ||
====== Throttle Cable ====== | ====== Throttle Cable ====== | ||
+ | There are a couple of things you will have to consider regarding a Mikuni installation. First is the throttle control. ((piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | ||
+ | The Bendix uses a solid wire and the Mikuni needs a flexible braid cable. \\ | ||
+ | So if you are now using the original enclosed hard wire in the handlebar you will need to swap for a drum type twist grip like the one below. \\ | ||
+ | The Mikuni is a tall carb and as a result you will need a 90° elbow on the throttle cable to route the cable under the gas tank. \\ | ||
+ | On a Sportster you must have this elbow. See the pics below. Trying to find this elbow with the proper throttle cable can sometimes be a chore. \\ | ||
+ | The throttle cable has a shorter outer housing (shorter by length of the elbow) than what you will have on a cable not using the elbow. \\ | ||
+ | You will need to connect the round carb body to the flanged manifold, so that requires an adapter. \\ | ||
+ | All this uses hose clamps to do the job. See the pic below showing the 2 clamps around the adapter. \\ | ||
+ | |||
+ | {{:techtalk:ref:carb:braided_throttle_cable_1_by_piniongear.jpg?direct&300|}} ((photo by piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) {{:techtalk:ref:carb:braided_throttle_cable_2_by_piniongear.jpg?direct&300|}} ((photo by piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=938090&page=3)) \\ | ||
+ | |||
File any rough spots from the ball end and / or open up the ferrule a bit with a flat blade screwdriver. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) \\ | File any rough spots from the ball end and / or open up the ferrule a bit with a flat blade screwdriver. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) \\ | ||
{{:techtalk:ref:carb:vm-38_project_10_by_ironmick.jpg?direct&250|}} ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) {{:techtalk:ref:carb:vm-38_project_11_by_ironmick.jpg?direct&300|}} ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) \\ | {{:techtalk:ref:carb:vm-38_project_10_by_ironmick.jpg?direct&250|}} ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) {{:techtalk:ref:carb:vm-38_project_11_by_ironmick.jpg?direct&300|}} ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1567528&page=2)) \\ |