Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:carb01v [2019/09/13 21:42]
hippysmack [S&S G, GA, GAL]
+++ techtalk:ref:carb01v [2019/09/15 02:09]
hippysmack [S&S GB & GBL]
@@ Line 82: / Line 82: @@
 GBL \\
-{{:techtalk:ref:carb:sands_carbs_10_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)){{:techtalk:ref:carb:sands_carbs_11_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)) \\
+This carb will be fine on an 88" motor. Here's the basic stuff you need to deal with. \\
+Manifold: use the Super B or Super E manifold. \\
+Air Cleaner: the entire Super B setup is a bolt on to L series. \\
+Throttle: this goes to the action cable of the 2 cable system. Forget the idle cable exists for now. \\
+All sportsters 1972> open the throttle plate when the inner cable retreats into the outer coil. \\
+In other words, the braided cable 'pulls' the throttle plate open. The L series (except mgl) is set up for the 1971< throttle plate actuation. \\
+In this setup the inner cable was not braided. It was a solid wire because the inner wire pushed the throttle plate open. \\
+You need to reverse this action at the carb.
+For instance: \\
+st get a Super B throttle shaft and install it in the GAL. It's longer on the forward end compared to the GAL shaft. \\
+The added length will allow you to install a second throttle lever assembly on the longer shaft. This lever is also Super B. \\
+See the first pic below. The shaft extension will be less (but still enough) on a GAL. \\
+{{:techtalk:ref:carb:sands_gbl_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=2004343&page=2)) {{:techtalk:ref:carb:sands_carbs_10_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)){{:techtalk:ref:carb:sands_carbs_11_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)) \\
 {{:techtalk:ref:carb:sands_gbl_carb_1_by_monte03.jpg?direct&300|}} ((photo by Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1022912&page=7)) {{:techtalk:ref:carb:sands_gbl_carb_2_by_monte03.jpg?direct&300|}} ((photo by Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1022912&page=7)) {{:techtalk:ref:carb:sands_gbl_carb_3_by_monte03.jpg?direct&300|}} ((photo by Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1022912&page=9)) \\
@@ Line 96: / Line 108: @@
 {{:techtalk:ref:carb:sands_modded_g_style_carb_1_by_mrmom.jpg?direct&300|}} ((photo by mrmom9r of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)) {{:techtalk:ref:carb:sands_modded_g_style_carb_2_by_mrmom.jpg?direct&300|}} ((photo by mrmom9r of the XLFORUM http://xlforum.net/forums/showthread.php?t=1786621)) \\
+====== Throttle Cable ======
+This GBL has a modded bracket to accept any cabling system (push or pull - solid or braided). \\
+{{:techtalk:ref:carb:sands_gbl_throttle_mod_1_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1932694&page=3)) {{:techtalk:ref:carb:sands_gbl_throttle_mod_2_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1932694&page=3)) {{:techtalk:ref:carb:sands_gbl_throttle_mod_3_by_dr_dick.jpg?direct&300|}} ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1932694&page=3)) \\
 \\

Trace:

Differences

Navigation

Search

Toolbox