Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Next revision Both sides next revision | ||
techtalk:ref:elec06 [2018/11/07 21:48] hippysmack [Other Pics of this Mod] |
techtalk:ref:elec06 [2018/11/19 23:25] hippysmack |
||
---|---|---|---|
Line 80: | Line 80: | ||
====== Tachometers ====== | ====== Tachometers ====== | ||
- | ====== Relocating Gauges (Speedo / Tach) ====== | ||
- | ====== Headlight Eyebrow Mounted Gauges ====== | ||
- | |||
- | ===== The Zena Mod ===== | ||
- | This is a relatively easy mod to raise the height of your instruments (when using taller risers). \\ | ||
- | Otherwise, the gauges end up being too tall. \\ | ||
- | The gauges are removed from the handlebar mount and bolted to the headlight eyebrow using deep chrome sockets. \\ | ||
- | Cost is under #10. Done carefully, it looks like a factory install. \\ | ||
- | |||
- | * Parts required: | ||
- | * (2) - chrome 8mm deep sockets (may be able to use other sizes) | ||
- | * (4) - stainless steel washers | ||
- | * (2) - 3" stainless steel allen bolts, \\ (same diameter as stock but longer to fit sockets accordingly. 3" bolts used below). | ||
- | |||
- | * Note: This mod should work without a hitch on the 883 std and 1200R. \\ | ||
- | * In some instances, folks have reported that the spacing between the holes on the gauge mount \\ did not line up perfectly with the holes on the eyebrow. | ||
- | * Most were able to quickly remedy the problem with a dremel or other comparable tool. \\ | ||
- | * The mod will not work on stock 1200/883 Custom models without additional modification. | ||
- | |||
- | |{{:techtalk:ref:elec:zena_mod_1_by_xena.jpg?direct&300|}}|{{:techtalk:ref:elec:zena_mod_2_by_xena.jpg?direct&300|}}|{{:techtalk:ref:elec:zena_mod_3_by_xena.jpg?direct&300|}}| | ||
- | | Relocating gauges ((photos by xena of the XLFORUM http://xlforum.net/forums/newreply.php?do=postreply&t=3883)) ||| | ||
- | |||
- | |||
- | ===== Variation of the Zena Mod ===== | ||
- | |||
- | |||
- | |Before. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))| | ||
- | |{{:techtalk:ref:elec:relocating_speedo_1_by_erik.jpg?direct&300|}}| | ||
- | |||
- | |After. ((photos by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))||| | ||
- | |{{:techtalk:ref:elec:relocating_speedo_11_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_13_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_12_by_erik.jpg?direct&300|}}| | ||
- | |||
- | |Removed upper bar clamp bolts \\ with a 1/4" Allen wrench. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))|OEM Handlebar spacers (5736). ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))|Added blue Loctite to the handlebar bolts. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))| | ||
- | |{{:techtalk:ref:elec:relocating_speedo_2_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_3_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_4_by_erik.jpg?direct&300|}}| | ||
- | |||
- | |Re-installed the bolts without speedo bracket. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))|Removed the eyebrow bolts with a 1/2" socket. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))|Replaced the OEM bolts with 1/4"x3-1/2" allen head \\ cap bolts. ((photo by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))| | ||
- | |{{:techtalk:ref:elec:relocating_speedo_5_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_6_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_7_by_erik.jpg?direct&300|}}| | ||
- | |||
- | |1/2" O.D.x1/4" I.D. sleeves slid over the bolts with washers under the head. \\ Sleeves go between the eyebrow and the gauge housing. ((photos by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=19))||| | ||
- | |{{:techtalk:ref:elec:relocating_speedo_8_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_9_by_erik.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_speedo_10_by_erik.jpg?direct&300|}}| | ||
- | |||
- | |||
- | ===== Other Pics of this Mod ===== | ||
- | |||
- | |Done on a 2001 1200S. \\ 1/2"x1-3/4" threaded rod couplers painted them black with 3-1/2" grade 8 bolts. ((photos by rokclmb of the XLFORUM http://xlforum.net/forums/showthread.php?t=533222))|| | ||
- | |{{:techtalk:ref:elec:relocating_01_1200s_gauges_1_by_rokclmb.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_01_1200s_gauges_2_by_rokclmb.jpg?direct&300|}}| | ||
- | |||
- | |Done on an 89 883. ((photos by engine of the XLFORUM http://xlforum.net/forums/showthread.php?postid=350420))|| | ||
- | |{{:techtalk:ref:elec:89_883_speedo_relocation_1_by_engine.jpg?direct&300|}}|{{:techtalk:ref:elec:89_883_speedo_relocation_2_by_engine.jpg?direct&300|}}| | ||
- | |||
- | |||
- | ====== Riser Mounted Gauges ====== | ||
- | ===== The ReddTigger Mod ===== | ||
- | Speedo Mount for pullback risers. \\ | ||
- | The biggest frustration is the angle of the stock mount that's used to mount onto the original handlebar clamp. \\ | ||
- | |||
- | * Parts (total of about $20): | ||
- | * 2 chrome socket head screws. | ||
- | * 2 chrome acorn nuts. | ||
- | * 2 chrome washers. | ||
- | * 2 chrome cable clamps for 1" (or whatever size your risers are). | ||
- | * 2 small pieces of tubing. | ||
- | |||
- | * Place the tubing in the cable end of the clamp. | ||
- | * Attach clamp to riser as shown below. | ||
- | * Attach speedo using stock bracket (or any of your choice). | ||
- | * Insert socket head screws w/ washers through stock bracket into hose in clamp. | ||
- | * Secure with acorn nuts. \\ (the white stuff around the riser is some white electrical tape to prevent scratching) ((photos by ReddTigger of the XLFORUM http://xlforum.net/forums/showthread.php?t=50229&page=2)) | ||
- | |||
- | |{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_1_by_reddtigger.jpg?direct&300|}}|{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_2_by_reddtigger.jpg?direct&300|}}|{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_3_by_reddtigger.jpg?direct&300|}}| | ||
- | |||
- | | A bungie cord across the bolts holds a water bottle in the middle ((photos by ReddTigger of the XLFORUM http://xlforum.net/forums/showthread.php?t=50229))|| | ||
- | |{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_4_by_reddtigger.jpg?direct&300|}}|{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_5_by_reddtigger.jpg?direct&300|}}| | ||
- | |||
- | |Here's what it looks like with a tach added. ((photos by ReddTigger of the XLFORUM http://xlforum.net/forums/showthread.php?t=50229))||| | ||
- | |{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_6_by_reddtigger.jpg?direct&300|}}|{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_7_by_reddtigger.jpg?direct&300|}}|{{:techtalk:ref:elec:speedo_mount_for_pullback_risers_8_by_reddtigger.jpg?direct&300|}}| | ||
- | |||
- | ===== Other Pics of the Mod ===== | ||
- | |||
- | | Riser mounted cable clamps installed on the risers for guage mounts ((photos by Choprocker of the XLFORUM http://xlforum.net/forums/showthread.php?t=3883&highlight=xena+mod&page=10)) || | ||
- | |{{:techtalk:ref:elec:relocating_gauges_1_by_choprocker.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_gauges_2_by_choprocker.jpg?direct&300|}}| | ||
- | |||
- | | Gauges mounted ((photos by Choprocker of the XLFORUM http://xlforum.net/forums/showthread.php?t=3883&highlight=xena+mod&page=10)) ||| | ||
- | |{{:techtalk:ref:elec:relocating_gauges_3_by_choprocker.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_gauges_4_by_choprocker.jpg?direct&300|}}|{{:techtalk:ref:elec:relocating_gauges_5_by_choprocker.jpg?direct&300|}}| | ||
\\ | \\ |