Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:engmech01b [2018/04/29 19:36]
hippysmack created
techtalk:ref:engmech01b [2018/04/29 21:14]
hippysmack [Timer Plate Hole Thread Repair]
Line 2: Line 2:
 ====== REF: Engine Mechanicals - Sub-01B ====== ====== REF: Engine Mechanicals - Sub-01B ======
 ====== Timer Plate Hole Thread Repair ====== ====== Timer Plate Hole Thread Repair ======
 +The hole threads are #8-32.
 +====== Installing a Helicoil ======
 +Using a helicoil repair insert to continue using your factory plate fastener.
  
 +  * The existing hole has to be pre-drilled with a #16 bit to accept the helicoil threads (max hole dia. to use this size helicoil is .177"​). ((McMaster-Carr https://​www.mcmaster.com/#​bushings/​=1cml8fv))
 +  * Tape the drill bit to mark how deep to drill using the helicoil length as a guide. Also take into account the tapered end of the drill bit (it will not be as wide as the main body of the bit on the end which could cause tap and the insert not to fully seat if this dimension is not accounted for).
 +  * Tap the hole as straight as possible (#16 is the pre-drill size for a #12-24 tap). ((Starrett tap drill chart))
 +  * Insert the helicoil with the insertion tool.
 +  * Break the installation tab with the tool in the kit or a hole punch.
 +  * Remove the tab with a small magnet. ​  
  
 +
 +|  Using a Helicoil Kit ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |  The proper drill bit is included to enlarge the hole \\ (to make room for the Helicoil) ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |
 +|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_1_by_fergerburger.jpg?​direct&​400|}}|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_2_by_fergerburger.jpg?​direct&​400|}}|
 +
 +|  Mark the bit with tape as a depth stop \\ (to keep from drilling too deep) ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |  Carefully tap the hole ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |
 +|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_3_by_fergerburger.jpg?​direct&​400|}}|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_4_by_fergerburger.jpg?​direct&​400|}}|
 +
 +|Install the helicoil with the insertion tool ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |  Break the tab off at the bottom with the punch and \\ remove it with a small magnet ​ ((Photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1071324)) ​ |
 +|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_5_by_fergerburger.jpg?​direct&​400|}}|{{:​techtalk:​ref:​engmech:​timer_plate_hole_thread_repair_6_by_fergerburger.jpg?​direct&​400|}}|