Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ref:engmech01q [2019/02/18 16:55] hippysmack [Roller end manuf. defect repair] |
techtalk:ref:engmech01q [2019/02/18 17:07] hippysmack [Roller end manuf. defect repair] |
||
|---|---|---|---|
| Line 91: | Line 91: | ||
| It seems aftermarket lifters have a tendency to be wide at the roller end (at the opposite pins holding the roller). \\ | It seems aftermarket lifters have a tendency to be wide at the roller end (at the opposite pins holding the roller). \\ | ||
| Measure them before installing to be sure they won't scratch the lifter bore when turned home. ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?p=5283285&highlight=lifter+pins#post5283285)) \\ | Measure them before installing to be sure they won't scratch the lifter bore when turned home. ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?p=5283285&highlight=lifter+pins#post5283285)) \\ | ||
| + | The Fueling lifters below had this problem. \\ | ||
| + | The company (when contacted) said they would replace them but with concerns of receiving the same issue with replacements, these were resized at the base. \\ | ||
| The lifter has to be installed in the top facing the flats toward the engine or it hangs up on the cylinder fins. \\ | The lifter has to be installed in the top facing the flats toward the engine or it hangs up on the cylinder fins. \\ | ||
| Line 117: | Line 119: | ||
| |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_11_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_11_by_hippysmack.jpg?direct&300|}}| | ||
| - | The hone was turned by hand for app. 10 turns (while holding the bushing in place) per lifter bore to clean up the scratches. | + | The hone was turned by hand for app. 10 turns (while holding the bushing in place) per lifter bore to clean up the scratches. \\ |
| + | Due to the slanted bores, the bushing was raised slightly while honing. \\ | ||
| |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_12_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_12_by_hippysmack.jpg?direct&300|}}| | ||
