Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ref:engmech01q [2019/02/18 17:07] hippysmack [Roller end manuf. defect repair] |
techtalk:ref:engmech01q [2019/02/18 17:15] hippysmack [Roller end manuf. defect repair] |
||
|---|---|---|---|
| Line 116: | Line 116: | ||
| The hone was made from a ball hone with the balls removed and 400 grit sandpaper Gorilla glued to the shaft. \\ | The hone was made from a ball hone with the balls removed and 400 grit sandpaper Gorilla glued to the shaft. \\ | ||
| To keep center on the hone, a bushing was cut on the lathe with a slip fit hole small enough to accept the wire handle. \\ | To keep center on the hone, a bushing was cut on the lathe with a slip fit hole small enough to accept the wire handle. \\ | ||
| - | |The bores are slanted toward the pushrod cup \\ of each rocker arm.| Homemade hone to lightly clean up the lifter bore. || | + | |The bores are slanted toward the pushrod cup \\ of each rocker arm. ((photo by Hippysmack))| Homemade hone to lightly clean up the lifter bore. ((photos by Hippysmack)) || |
| |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_11_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_11_by_hippysmack.jpg?direct&300|}}| | ||
| The hone was turned by hand for app. 10 turns (while holding the bushing in place) per lifter bore to clean up the scratches. \\ | The hone was turned by hand for app. 10 turns (while holding the bushing in place) per lifter bore to clean up the scratches. \\ | ||
| Due to the slanted bores, the bushing was raised slightly while honing. \\ | Due to the slanted bores, the bushing was raised slightly while honing. \\ | ||
| + | |Hone held through center of pushrod hole. ((photo by Hippysmack))|This is all that was removed from all 4 bores \\ combined. ((photo by Hippysmack))|All scratches weren't removed but honing too much \\ would open the bore too far. ((photo by Hippysmack))| | ||
| |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_12_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_12_by_hippysmack.jpg?direct&300|}}| | ||
