Differences
This shows you the differences between two versions of the page.
Next revision Both sides next revision | |||
techtalk:ref:engmech02e [2019/03/10 03:26] hippysmack created |
techtalk:ref:engmech02e [2019/03/10 03:37] hippysmack [Removing / Installing Piston Rings] |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== REF: Engine Mechanicals - Sub-02E ====== | ====== REF: Engine Mechanicals - Sub-02E ====== | ||
====== Removing / Installing Piston Rings ====== | ====== Removing / Installing Piston Rings ====== | ||
+ | **Removal**: \\ | ||
+ | Some just peel the top 2 rings off by hand the same as removing the oil rings. \\ | ||
+ | Older rings were notorious for breaking when one end was spread too far vertically. \\ | ||
+ | This still can happen on modern rings but they can be carefully wound on / off by hand. \\ | ||
+ | |||
+ | A piston ring spreader is used below. \\ | ||
+ | The ring spreader hooks both ends of the ring and spreads it apart making the inside diameter wider than the piston. \\ | ||
+ | Then you simply center the widened ring around the piston and lift it up and off. \\ | ||
+ | |||
+ | **Caution**: only spread the ring just enough to remove / install the ring. | ||
+ | |||
|{{:techtalk:ref:tools:piston_ring_spreader_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_1_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:tools:piston_ring_spreader_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_1_by_hippysmack.jpg?direct&300|}}| | ||
|{{:techtalk:ref:engmech:removing_piston_rings_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_4_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:removing_piston_rings_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_4_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | The oil rings are usually removed by hand. \\ | ||
|{{:techtalk:ref:engmech:removing_piston_rings_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_7_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:removing_piston_rings_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:removing_piston_rings_7_by_hippysmack.jpg?direct&300|}}| |