Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:engmech03e [2019/05/28 03:08] hippysmack [Chopping the Cam / Gearcase Cover] |
techtalk:ref:engmech03e [2020/08/20 23:43] hippysmack |
||
---|---|---|---|
Line 4: | Line 4: | ||
See also: \\ | See also: \\ | ||
- | * [[techtalk:ref:engmech03e#pics_of_cam_gearcase_cover_mods|Pics of Cam / Gearcase Cover Mods]] | + | * [[techtalk:ref:engmech03f#pics_of_cam_gearcase_cover_mods|Pics of Cam / Gearcase Cover Mods]] |
- | * [[techtalk:ref:engmech03f#pics_of_sprocket_cover_mods|Pics of Sprocket Cover Mods]] | + | * [[techtalk:ref:engmech03j#pics_of_sprocket_cover_mods|Pics of Sprocket Cover Mods]] |
* [[techtalk:ref:engmech03a#ignition_cover_mods_and_aftermarket_covers|Ignition Cover Mods and Aftermarket Covers]] | * [[techtalk:ref:engmech03a#ignition_cover_mods_and_aftermarket_covers|Ignition Cover Mods and Aftermarket Covers]] | ||
* [[techtalk:ref:svcproc45#refshop_notes_and_tips|Polishing Aluminum]] | * [[techtalk:ref:svcproc45#refshop_notes_and_tips|Polishing Aluminum]] | ||
Line 29: | Line 29: | ||
Some have a factory drilled oil passage (1/8") through the cover going to the pinion bushing area. The hole on the lower edge of the cam cover was then welded to seal this hole. ((ericfreeman http://xlforum.net/forums/showthread.php?t=467551&page=2)) \\ | Some have a factory drilled oil passage (1/8") through the cover going to the pinion bushing area. The hole on the lower edge of the cam cover was then welded to seal this hole. ((ericfreeman http://xlforum.net/forums/showthread.php?t=467551&page=2)) \\ | ||
- | After cutting thru this hole, it can be plugged again by running a 1/4"x20 tap in and threading a screw into it with JB weld / epoxy applied. ((Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=525868)) | + | After cutting thru this hole, it can be plugged again by running a 1/4"x20 tap in and threading a screw into it (with a copper washer). ((Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=525868)) \\ |
- | |{{:techtalk:ref:engmech:cam_cover_mod_9_by_johnny_wolf.jpg?direct&300|}}|{{:techtalk:ref:engmech:cam_cover_mod_10_by_johnny_wolf.jpg?direct&300|}}| | + | It is not a overflow hole or anything that should be open. \\ |
+ | Some have used silicone or epoxy to plug the hole. However, some have also had silicone break loose from heat and plug up vital oil passages. \\ | ||
+ | So a threaded plug / bolt is best to use. \\ | ||
+ | |||
+ | |{{:techtalk:ref:engmech:cam_cover_mod_with_plug_2_by_falcoflash.jpg?direct&300|}} ((photo by FalcoFlash of the XLFORUM http://xlforum.net/forums/showthread.php?t=2077245))|{{:techtalk:ref:engmech:cam_cover_mod_9_by_johnny_wolf.jpg?direct&300|}}|{{:techtalk:ref:engmech:cam_cover_mod_with_plug_1_by_falcoflash.jpg?direct&300|}} ((photo by FalcoFlash of the XLFORUM http://xlforum.net/forums/showthread.php?t=2077245)) | | ||
**Dowel Pins**: \\ | **Dowel Pins**: \\ |