Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:engmech05 [2019/07/18 19:04] hippysmack [Filter on End of the Vent Line] |
techtalk:ref:engmech05 [2019/07/26 17:34] hippysmack [Vent Outlet Above vs Below the Head Vents] |
||
---|---|---|---|
Line 31: | Line 31: | ||
However, exact line routing comes down to function over fashion. \\ | However, exact line routing comes down to function over fashion. \\ | ||
While it may look better or cleaner for the lines to be routed above the air cleaner; \\ | While it may look better or cleaner for the lines to be routed above the air cleaner; \\ | ||
- | Doing so doesn't make for good functioning of the breather system. \\ | + | Doing so doesn't necessarily make for good functioning of the breather system. \\ |
+ | That also can be debated. \\ | ||
The air / oil that gets blown out is a combination of crankcase pressure and engine blowby. \\ | The air / oil that gets blown out is a combination of crankcase pressure and engine blowby. \\ | ||
- | Blowby gasses produce a corrosive vapor which doesn't need to go back into the engine. \\ | + | The argument is blowby gasses produce a corrosive vapor which doesn't need to go back into the engine. \\ |
- | It'll simply pool in the heads / vent lines. \\ | + | It'll simply pool in the heads / vent lines and become an emulsified goop. \\ |
Mounting vent lines higher than the head vents is counterproductive to quick air/oil/condensate removal. \\ | Mounting vent lines higher than the head vents is counterproductive to quick air/oil/condensate removal. \\ | ||
It's the quick removal that helps prevent sludge buildup. \\ | It's the quick removal that helps prevent sludge buildup. \\ | ||
Line 46: | Line 47: | ||
The air coming from the head vents has fine water condensation and oil mist particles in suspension with it. \\ | The air coming from the head vents has fine water condensation and oil mist particles in suspension with it. \\ | ||
- | When that air cools, the oil mist falls out of suspension and collects in the vent lines. \\ | + | When that air cools, the oil mist falls out of suspension and collects in the vent lines and mixing with unsuspended oil droplets. \\ |
Pointing the vent lines straight into the A/C (OEM) or down into a catch can allows the oil out of suspension to leave the vent lines. \\ | Pointing the vent lines straight into the A/C (OEM) or down into a catch can allows the oil out of suspension to leave the vent lines. \\ | ||
Line 52: | Line 53: | ||
However, pointing the vent lines upward of the head vents allows oil out of suspension to collect in them. \\ | However, pointing the vent lines upward of the head vents allows oil out of suspension to collect in them. \\ | ||
Once there is enough liquid oil in the upward breather tubes it will act just like the trap under your sink. \\ | Once there is enough liquid oil in the upward breather tubes it will act just like the trap under your sink. \\ | ||
- | It may block air from getting out until the engine (on startup) builds enough pressure to push the liquid and bubble up to the top. \\ | + | It may restrict or block air from getting out until the engine (on startup) builds enough pressure to push the liquid and bubble up to the top. \\ |
So it may affect crankcase pressure slightly until the lines are cleared. \\ | So it may affect crankcase pressure slightly until the lines are cleared. \\ | ||
Or the trapped oil may simply be blown out the vent lines in globs. \\ | Or the trapped oil may simply be blown out the vent lines in globs. \\ | ||
Line 148: | Line 149: | ||
====== Pics of Aftermarket Breather Valves ====== | ====== Pics of Aftermarket Breather Valves ====== | ||
- | |Doherty Power Vents with the line routed up then \\ down and attached to the bottom of the frame. ((photo by RIORoosen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=18))| | + | |Doherty Power Vents with the line routed up then \\ down and attached to the bottom of the frame. ((photo by RIORoosen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=18))|Hayden KVP38 breather valve, used with the \\ [[techtalk:ref:engmech05d|Deimus Mod]] (cam chest breather conversion). ((photo by 60Gunner of the XLFORUM http://xlforum.net/forums/showthread.php?p=5763918#post5763918))| |
- | |{{:techtalk:ref:engmech:breather_mod_by_rioroosen.jpg?direct&300|}}| | + | |{{:techtalk:ref:engmech:breather_mod_by_rioroosen.jpg?direct&300|}}|{{:techtalk:ref:engmech:deimus_mod_8_by_60gunner.jpg?direct&300|}}| |