Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:engmech05a [2019/07/16 15:24] hippysmack [Drag Specialties Breather Location Kit (EFI)] |
techtalk:ref:engmech05a [2020/10/25 15:17] hippysmack [Using Spark Plug Boot Connectors] |
||
|---|---|---|---|
| Line 32: | Line 32: | ||
| The spark plug boots should fit snug. \\ | The spark plug boots should fit snug. \\ | ||
| Route the hose with as few bends as needed and the filter out of the way. | Route the hose with as few bends as needed and the filter out of the way. | ||
| + | |||
| + | **Note**: \\ | ||
| + | Heat may soften the rubber over time and the rubber boots will have to be replaced to keep oil from leaking around them. \\ | ||
| | Hose splices in the spark plug boots. ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))|Holes drilled in backing plate (not necessary). ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))|Plastic hose "T" to splice both ends together. ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))| | | Hose splices in the spark plug boots. ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))|Holes drilled in backing plate (not necessary). ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))|Plastic hose "T" to splice both ends together. ((photo by 1200C of the XLFORUM http://xlforum.net/forums/showthread.php?t=47848))| | ||
| Line 42: | Line 45: | ||
| |{{techtalk:ref:engmech:breather_mod_7_by_1200c.jpg?direct&300|}}| | |{{techtalk:ref:engmech:breather_mod_7_by_1200c.jpg?direct&300|}}| | ||
| + | ===== Vent Line Routing Pics ===== | ||
| - | ===== Drag Specialties Breather Location Kit (07-UP) ===== | + | | Stainless breather hoses routed to the ground. ((photo by renpia of the XLFORUM http://xlforum.net/forums/showthread.php?p=741784)) | |
| - | The DS kit is in the right pic below plus gasket maker (not necessary) and Loctite. \\ | + | |{{:techtalk:ref:engmech:breather_mod_1_by_renpia.jpg?direct&300|}}| |
| - | Bracket. \\ | + | |
| - | Breather bolts. \\ | + | |
| - | Banjo fittings and fiber washers. \\ | + | |
| - | + | ||
| - | |There are 3 holes for mounting the A/C & carb. \\ One on each head / one centered to the intake. ((photo by Hagen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11))|Drag Specialties relocation kit. ((photo by Hagen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11))| | + | |
| - | |{{:techtalk:ref:engmech:breather_mod_3_by_hagen.jpg?direct&300|}}|{{:techtalk:ref:engmech:breather_mod_4_by_hagen.jpg?direct&300|}}| | + | |
| - | + | ||
| - | + | ||
| - | |Bracket and breather bolts installed. ((photo by Hagen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11))|Hoses run down under the intake. ((photo by Hagen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11))|NRHS backing plate hiding the assembly. ((photo by Hagen of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11))| | + | |
| - | |{{:techtalk:ref:engmech:breather_mod_5_by_hagen.jpg?direct&300|}}|{{:techtalk:ref:engmech:breather_mod_6_by_hagen.jpg?direct&300|}}|{{:techtalk:ref:engmech:breather_mod_7_by_hagen.jpg?direct&300|}}| | + | |
| \\ | \\ | ||
