Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:engmech05d [2019/07/21 02:23] hippysmack [Installing the Ultimate Crankcase Vent] |
techtalk:ref:engmech05d [2019/08/17 16:23] hippysmack [Baffle] |
||
---|---|---|---|
Line 102: | Line 102: | ||
Alternate way of making the baffle: ((60Gunner of the XLFORUM http://xlforum.net/forums/showthread.php?p=5763918#post5763918)) \\ | Alternate way of making the baffle: ((60Gunner of the XLFORUM http://xlforum.net/forums/showthread.php?p=5763918#post5763918)) \\ | ||
+ | The wings were initially 1" inward each before bending. \\ | ||
+ | While fitting, they were cut back to 1/2" each and the side with the fitting was cut again at about a 1/4" for clearance of the fitting. \\ | ||
+ | This baffle started out with as piece 5"x2" cut sheet metal, bent an inch on each end for the wings. \\ | ||
+ | 5/8" of the bottom of the flaps were cut off. \\ | ||
+ | The cover tapers roughly 45° in and down at that point from there down to bottom. \\ | ||
+ | A Dremel rotary tool was used to round all edges and the corners slightly. \\ | ||
+ | It was tight to the bottom then another 1/8" was cut because it was just flush with the gasket surface (dropped it slightly). \\ | ||
+ | |||
The baffle should be pretty snug when installed. You should have to lift a little on one side then the other back and forth to remove it. \\ | The baffle should be pretty snug when installed. You should have to lift a little on one side then the other back and forth to remove it. \\ | ||
The sheet metal was bent with my a small hand brake then the flaps were trimmed to fit. \\ | The sheet metal was bent with my a small hand brake then the flaps were trimmed to fit. \\ | ||
Line 115: | Line 123: | ||
===== Baffle ===== | ===== Baffle ===== | ||
+ | {{:techtalk:ref:engmech:deimus_mod_2_by_grind.jpg?direct&300|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) \\ | ||
{{:techtalk:ref:engmech:deimus_mod_1_by_bassboy311.jpg?direct&300|}} ((photo by bassboy311 of the XLFORUM http://xlforum.net/forums/showthread.php?t=72099&highlight=wet+sumping&page=6)) {{:techtalk:ref:engmech:deimus_mod_1_by_kirk_the_jerk.jpg?direct&300|}} ((photo by Kirk the Jerk of the XLFORUM http://xlforum.net/forums/showthread.php?t=826526)) {{:techtalk:ref:engmech:deimus_mod_2_by_kirk_the_jerk.jpg?direct&300|}} ((photo by Kirk the Jerk of the XLFORUM http://xlforum.net/forums/showthread.php?t=826526)) \\ | {{:techtalk:ref:engmech:deimus_mod_1_by_bassboy311.jpg?direct&300|}} ((photo by bassboy311 of the XLFORUM http://xlforum.net/forums/showthread.php?t=72099&highlight=wet+sumping&page=6)) {{:techtalk:ref:engmech:deimus_mod_1_by_kirk_the_jerk.jpg?direct&300|}} ((photo by Kirk the Jerk of the XLFORUM http://xlforum.net/forums/showthread.php?t=826526)) {{:techtalk:ref:engmech:deimus_mod_2_by_kirk_the_jerk.jpg?direct&300|}} ((photo by Kirk the Jerk of the XLFORUM http://xlforum.net/forums/showthread.php?t=826526)) \\ |