Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Last revision Both sides next revision | ||
techtalk:ref:genmsr12 [2019/01/09 02:19] ixl2relax ↷ Links adapted because of a move operation |
techtalk:ref:genmsr12 [2019/02/12 01:08] hippysmack [Carburetor Cleaner] |
||
---|---|---|---|
Line 19: | Line 19: | ||
Make sure to remove any rubber or plastic parts before soaking. \\ | Make sure to remove any rubber or plastic parts before soaking. \\ | ||
Also check the label for safety precautions. \\ | Also check the label for safety precautions. \\ | ||
- | Parts that have been sitting for years may have to be soaked for about 24 hours. \\ | + | Parts that have been sitting for years may have to be soaked for about 24 hours or more. \\ |
- | | Carburetor Cleaner ((photo by Hippysmack)) ||| | + | | These pistons below were soaked for app. 5 days rinsing each night to remove carbon on top. ((photos by balduc-2 of the XLFORUM http://xlforum.net/forums/showthread.php?s=731c426f4dea033958967a4ac51dfc9e&p=4810490)) || |
+ | |{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_1_by_balduc-2.jpg?direct&300|}}|{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_2_by_balduc-2.jpg?direct&300|}}| | ||
+ | |||
+ | | This oil pump soaked overnite to loosen the body to cover gasket. ((photo by Hippysmack)) ||| | ||
|{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_4.1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}| | |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_4.1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}| | ||
This oil pump had to be soaked overnite before the cover would separate from the body. \\ | This oil pump had to be soaked overnite before the cover would separate from the body. \\ | ||
Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ | Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ | ||
- | | Soaking gaskets for more easy removal ((photos by Hippysmack)) ||| | + | | After soaking, rinse the body, take it apart and rinse the insides and parts. ((photos by Hippysmack)) ||| |
|{{techtalk:ref:genmsr:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_5_by_hippysmack.jpg?direct&300|}}| | |{{techtalk:ref:genmsr:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_5_by_hippysmack.jpg?direct&300|}}| | ||