Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
techtalk:ref:genmsr12 [2018/05/20 20:52] ixl2relax ↷ Page name changed from techtalk:ref:notes01 to techtalk:ref:notes106 |
techtalk:ref:genmsr12 [2024/01/17 23:14] (current) hippysmack |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | ====== REF: Shop Notes and Tips ====== | + | ====== REF: General-MSR 12 ====== |
| Line 6: | Line 6: | ||
| + | ==== Carburetor Cleaner ==== | ||
| + | Carburetor cleaner is not just for cleaning carbs and their parts. \\ | ||
| + | A gallon of carburetor cleaner is very useful in cleaning most any parts, bolts and other metals and soaking stuck gaskets. \\ | ||
| + | There is a metal bucket with a handle inside so you can put in small parts and remove them with the handle easily without loosing any. \\ | ||
| + | Insert small parts, bolts, wrenches or whatever you need to clean, close the lid and let them soak. \\ | ||
| + | Later, open the lid, remove the small bucket inside by the handle, set the bucket on the ground and wash the parts cleaner off with a water hose. \\ | ||
| + | Let them air dry and most, if not all of the grease/grime should be gone. \\ | ||
| + | You may have to re-soak heavy grimed parts or use a wire brush to break grime hardened areas before soaking again. \\ | ||
| + | |||
| + | For soaking stuck gaskets between mated parts to loosen them, \\ | ||
| + | Depending on how old or how 'stuck' the parts are, soaking for a couple hours may help to separate the old gasket in between. \\ | ||
| + | Make sure to remove any rubber or plastic parts before soaking. \\ | ||
| + | Also check the label for safety precautions. \\ | ||
| + | Parts that have been sitting for years may have to be soaked for about 24 hours or more. \\ | ||
| + | |||
| + | | These pistons below were soaked for app. 5 days rinsing each night to remove carbon on top. ((photos by balduc-2 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/163867-cam-cover-removal/page2?s=731c426f4dea033958967a4ac51dfc9e#post3495246)) || | ||
| + | |{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_1_by_balduc-2.jpg?direct&300|}}|{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_2_by_balduc-2.jpg?direct&300|}}| | ||
| + | |||
| + | | This oil pump soaked overnite to loosen the body to cover gasket. ((photo by Hippysmack)) ||| | ||
| + | |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_4.1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | This oil pump had to be soaked overnite before the cover would separate from the body. \\ | ||
| + | Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ | ||
| + | | After soaking, rinse the body, take it apart and rinse the insides and parts. ((photos by Hippysmack)) ||| | ||
| + | |{{techtalk:ref:genmsr:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_5_by_hippysmack.jpg?direct&300|}}| | ||
| ==== Spray-on Brake Cleaner ==== | ==== Spray-on Brake Cleaner ==== | ||
| Line 17: | Line 42: | ||
| ---- | ---- | ||
| - | + | \\ | |
| - | + | ||
| - | + | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
