Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
techtalk:ref:genmsr12 [2019/01/09 02:19]
ixl2relax ↷ Links adapted because of a move operation
techtalk:ref:genmsr12 [2019/02/12 01:08] (current)
hippysmack [Carburetor Cleaner]
Line 19: Line 19:
 Make sure to remove any rubber or plastic parts before soaking. \\ Make sure to remove any rubber or plastic parts before soaking. \\
 Also check the label for safety precautions. \\ Also check the label for safety precautions. \\
-Parts that have been sitting for years may have to be soaked for about 24 hours. \\+Parts that have been sitting for years may have to be soaked for about 24 hours or more. \\
  
-|  ​Carburetor Cleaner ​((photo by Hippysmack)) ​ |||+|  ​These pistons below were soaked for app. 5 days rinsing each night to remove carbon on top. ((photos by balduc-2 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​s=731c426f4dea033958967a4ac51dfc9e&​p=4810490)) ​ || 
 +|{{:​techtalk:​ref:​genmsr:​cleaning_pistons_with_chem_dip_1_by_balduc-2.jpg?​direct&​300|}}|{{:​techtalk:​ref:​genmsr:​cleaning_pistons_with_chem_dip_2_by_balduc-2.jpg?​direct&​300|}}| 
 + 
 +|  This oil pump soaked overnite to loosen the body to cover gasket. ​((photo by Hippysmack)) ​ |||
 |{{techtalk:​ref:​genmsr:​parts_cleaner_1_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_4.1_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_3_by_hippysmack.jpg?​direct&​300|}}| |{{techtalk:​ref:​genmsr:​parts_cleaner_1_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_4.1_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_3_by_hippysmack.jpg?​direct&​300|}}|
  
 This oil pump had to be soaked overnite before the cover would separate from the body. \\ This oil pump had to be soaked overnite before the cover would separate from the body. \\
 Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\
-|  ​Soaking gaskets for more easy removal ​((photos by Hippysmack)) ​ |||+|  ​After soaking, rinse the body, take it apart and rinse the insides and parts. ​((photos by Hippysmack)) ​ |||
 |{{techtalk:​ref:​genmsr:​parts_cleaner_4_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_5_by_hippysmack.jpg?​direct&​300|}}| |{{techtalk:​ref:​genmsr:​parts_cleaner_4_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​genmsr:​parts_cleaner_5_by_hippysmack.jpg?​direct&​300|}}|