Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:oil05h [2019/08/17 15:53] hippysmack [norseXL's 1986 Engine Oiling Mods] |
techtalk:ref:oil05h [2019/08/17 15:59] hippysmack [norseXL's 1986 Engine Oiling Mods] |
||
|---|---|---|---|
| Line 22: | Line 22: | ||
| A windage tray was made with a 2mm thick aluminum plate to also act as a flywheel scraper. \\ | A windage tray was made with a 2mm thick aluminum plate to also act as a flywheel scraper. \\ | ||
| The front part was bent toward the fly-wheels after the pic below was taken. ((norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1833647)) \\ | The front part was bent toward the fly-wheels after the pic below was taken. ((norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1833647)) \\ | ||
| - | The bolts are secured with Loctite (2701). \\ | + | The bolts are secured with Loctite (2701). \\ |
| + | See more on [[techtalk:ref:engmech01s|Windage Trays]] in the Sportsterpedia. \\ | ||
| | Reed valve. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341)) | Homemade windage tray. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341)) | | | Reed valve. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341)) | Homemade windage tray. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341)) | | ||
| |{{:techtalk:ref:oil:reed_valve_by_norsexl.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_windage_tray_by_norsexl.jpg?direct&300|}}| | |{{:techtalk:ref:oil:reed_valve_by_norsexl.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_windage_tray_by_norsexl.jpg?direct&300|}}| | ||
| - | Cam box oiling was also modified. \\ | + | Cam box oil routing was also modified. \\ |
| A line was tapped into the bottom of the case so the oil level doesn't rise above the castings for the bolts to flow to the scavenge hole at the rear of the crankcase. \\ | A line was tapped into the bottom of the case so the oil level doesn't rise above the castings for the bolts to flow to the scavenge hole at the rear of the crankcase. \\ | ||
| Also an external drain was plumbed from the cam chest to the crankcase (under the windage-plate). \\ | Also an external drain was plumbed from the cam chest to the crankcase (under the windage-plate). \\ | ||
| + | | Cam floor drain tube. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341&page=2)) | Lowering cam box drainage. ((photo by norseXL of the XLFORUM http://xlforum.net/forums/showthread.php?t=1386341&page=2)) | | ||
| |{{:techtalk:ref:oil:lowering_oil_level_in_cam_box_floor_by_norsexl.jpg?direct&300|}}|{{:techtalk:ref:oil:external_cam_floor_drain_by_norsexl.jpg?direct&300|}}| | |{{:techtalk:ref:oil:lowering_oil_level_in_cam_box_floor_by_norsexl.jpg?direct&300|}}|{{:techtalk:ref:oil:external_cam_floor_drain_by_norsexl.jpg?direct&300|}}| | ||
