Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:raw01 [2021/03/26 05:31]
hippysmack [Ironhead Frames - Various XLF Members]
+++ techtalk:ref:raw01 [2023/06/21 03:07]
ixl2relax
@@ Line 8: / Line 8: @@
+====== Electrical Compatibility Information ======
+submitted by Andy56 ((Post#179 - http://xlforum.net/forums/showthread.php?t=2039687))
+**Oil pressure switch**\\
+HD part number -- Standard Automotive\\
+- - - - - - - - - - - - - Products part number\\
+-72 - - - - - - MC1801\\
+-77 - - - - - - MC1802\\
+-84 - - - - - - MC1803\\
+-99 - - - - - - MC1804\\
+**Brush sets**\\
+HD part number -- Standard Motor\\
+- - - - - - - - - - - - - Products part number\\
+-58 - - - - - - MC2309\\
+**Starter Relay** TC models (2000-2011) V-ROD (2007-2011)\\
+-00B - - - - - - Durite 0-728-13, Standard Motor Products MC-RLY5\\
+**Suggested wire sizes** based on continuous load for standard multicore wire\\
+gauge (2.0mm2) 15 Amps\\
+gauge (1.3mm2) 7 Amps\\
+gauge (0.82mm2) 5 Amps\\
+gauge (0.5mm2) 3 Amps\\
+For lighting 1 watt = 0.07 Amps so a single 21W bulb takes 21x0.07 = 1.47 Amps\\
+Volt drop calculator for calculating wire size. (maximum acceptable volt drop nomaly 3-4%)\\
+https://www.rapidtables.com/calc/wir...alculator.html\\
+But remember the wire size has to be rated to the fuse it has to blow and not necessarily the continuous load.\\
+- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
+\\
+====== Suspension Info by ???? ======
 Comments: (by who??)
@@ Line 534: / Line 573: @@
 Destination - IH Body Parts
-Dr Dick http://xlforum.net/forums/showthread.php?t=1615459&page=3 \\
-frames 52-76 interchange. short frame was 52-66 all and 67-69ch. long were the other yrs/models.
-to change from one to the other you need: frame, swing arm (also long or short. its the swing arm that varies the wheel base), driver peg supports
-using the short frame with hump (long fame) motors will require some kind of solution of side stand contacting primary drain plug and boss.
-the pri drain is a hump motor thing. to intergrate its addition to the cases the footpeg mounting points and kickstand tab were moved forward on the long. frame. hence the different driver peg supports to bring pegs back into position. \\
 and earlier.......... \\
@@ Line 565: / Line 599: @@
 Also know as the start of the long frame Sportsters. \\
- and later.........… \\
+-1978.........… \\
 piniongear http://xlforum.net/forums/showthread.php?t=1476377 \\
@@ Line 574: / Line 608: @@
 This is how it came from the factory and has the different wiring harness to back that up.
 H-D mixed and matched with this feature it seems. \\
+-1985.......... \\
+Chevelle http://xlforum.net/forums/showthread.php?t=1514522 \\
+Like I stated, I have installed earlier engines in newer frames, but not vice versa.
+This does not necessarily apply to his post, just mentioning to possibly inform anyone who's interested.
+If using a 82-84 frame the front plates are larger like the early style, but the 82-84 plates are shaped differently and only work for 82-84.
+The same goes for a 82-84 rear motor mount.
+The early engine will not fit into a 82-84 w/o the 82-up rear mount.
+I assume the same for 77-up engines, they will only fit into 82-up frame w/ 82-up rear mount.
+ I do not know if a 77-up engine will fit into an earlier frame.
+ I don't know if a 82-up rear mount in this situation would be needed or not.
+ I don't know if it will physically fit (the sump) between the frame rails.
+ I do know a EVO enginewill fit into a 82 frame.
+ This was only after my buddy attempted to do it.
+ He was told over and over on different Internet sites that it was impossible. \\
+Threads: \\
+"Ironhead Animal Mother Reigns!" by snow http://xlforum.net/forums/showthread.php?t=1615459 \\
 ====== Who - Subject ======
 \\
 [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]

Trace:

Differences

Navigation

Search

Toolbox