Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:raw01 [2021/03/26 05:42] hippysmack [Ironhead Frames - Various XLF Members] |
techtalk:ref:raw01 [2023/06/21 03:07] ixl2relax |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| - | + | ====== Electrical Compatibility Information ====== | |
| + | submitted by Andy56 ((Post#179 - http://xlforum.net/forums/showthread.php?t=2039687)) | ||
| + | |||
| + | **Oil pressure switch**\\ | ||
| + | |||
| + | HD part number -- Standard Automotive\\ | ||
| + | - - - - - - - - - - - - - Products part number\\ | ||
| + | 26552-72 - - - - - - MC1801\\ | ||
| + | 26554-77 - - - - - - MC1802\\ | ||
| + | 26561-84 - - - - - - MC1803\\ | ||
| + | 26561-99 - - - - - - MC1804\\ | ||
| + | |||
| + | **Brush sets**\\ | ||
| + | |||
| + | HD part number -- Standard Motor\\ | ||
| + | - - - - - - - - - - - - - Products part number\\ | ||
| + | 30426-58 - - - - - - MC2309\\ | ||
| + | |||
| + | **Starter Relay** TC models (2000-2011) V-ROD (2007-2011)\\ | ||
| + | 31522-00B - - - - - - Durite 0-728-13, Standard Motor Products MC-RLY5\\ | ||
| + | |||
| + | **Suggested wire sizes** based on continuous load for standard multicore wire\\ | ||
| + | 14 gauge (2.0mm2) 15 Amps\\ | ||
| + | 16 gauge (1.3mm2) 7 Amps\\ | ||
| + | 18 gauge (0.82mm2) 5 Amps\\ | ||
| + | 20 gauge (0.5mm2) 3 Amps\\ | ||
| + | |||
| + | |||
| + | For lighting 1 watt = 0.07 Amps so a single 21W bulb takes 21x0.07 = 1.47 Amps\\ | ||
| + | |||
| + | Volt drop calculator for calculating wire size. (maximum acceptable volt drop nomaly 3-4%)\\ | ||
| + | https://www.rapidtables.com/calc/wir...alculator.html\\ | ||
| + | |||
| + | But remember the wire size has to be rated to the fuse it has to blow and not necessarily the continuous load.\\ | ||
| + | |||
| + | - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - | ||
| + | |||
| + | \\ | ||
| + | ====== Suspension Info by ???? ====== | ||
| Comments: (by who??) | Comments: (by who??) | ||
| Line 534: | Line 573: | ||
| Destination - IH Body Parts | Destination - IH Body Parts | ||
| - | Dr Dick http://xlforum.net/forums/showthread.php?t=1615459&page=3 \\ | ||
| - | frames 52-76 interchange. short frame was 52-66 all and 67-69ch. long were the other yrs/models. | ||
| - | to change from one to the other you need: frame, swing arm (also long or short. its the swing arm that varies the wheel base), driver peg supports | ||
| - | using the short frame with hump (long fame) motors will require some kind of solution of side stand contacting primary drain plug and boss. | ||
| - | the pri drain is a hump motor thing. to intergrate its addition to the cases the footpeg mounting points and kickstand tab were moved forward on the long. frame. hence the different driver peg supports to bring pegs back into position. \\ | ||
| 1972 and earlier.......... \\ | 1972 and earlier.......... \\ | ||
| Line 592: | Line 626: | ||
| He was told over and over on different Internet sites that it was impossible. \\ | He was told over and over on different Internet sites that it was impossible. \\ | ||
| + | Threads: \\ | ||
| + | "Ironhead Animal Mother Reigns!" by snow http://xlforum.net/forums/showthread.php?t=1615459 \\ | ||
| ====== Who - Subject ====== | ====== Who - Subject ====== | ||
| \\ | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
