Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
techtalk:ref:susp02d [2022/12/04 01:42] ixl2relax |
techtalk:ref:susp02d [2024/01/20 21:44] (current) hippysmack |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| My front forks (1994 XLH Std) were in need of rebuilding. So I purchased all the wearable parts and disassembled both front forks. I replaced all these parts and put new fluid in the forks - I used a no-name ATF for the fork oil, it being about 5-10wt oil. | My front forks (1994 XLH Std) were in need of rebuilding. So I purchased all the wearable parts and disassembled both front forks. I replaced all these parts and put new fluid in the forks - I used a no-name ATF for the fork oil, it being about 5-10wt oil. | ||
| - | At the same time, I replaced my stock fork springs with the Progressive 11-1527 springs. This spring kit is designated for rubbermount models, but the spring specs match for 91-later models as well. But the spacer needed to be shortened. | + | At the same time, I replaced my stock fork springs with the Progressive 11-1527 springs. This spring kit is designated for rubbermount models, but the spring specs match for 88-later models with 39mm tubes. But the spacer needed to be shortened. |
| - | The XLForum Thread about this is [[http://xlforum.net/forums/showthread.php?t=2006111|HERE]] by IXL2Relax. | + | The XLForum Thread about this is [[https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/188361-progressive-fork-springs-11-1527?t=2006111|HERE]] by IXL2Relax. |
| {{:techtalk:ref:susp:forkspring-prog-11-1527-install-1.jpg?800|}} | {{:techtalk:ref:susp:forkspring-prog-11-1527-install-1.jpg?800|}} | ||
| Line 24: | Line 24: | ||
| | || ::: | Kit# 11-1124 has a 3.50" Spacer) | | | || ::: | Kit# 11-1124 has a 3.50" Spacer) | | ||
| | My Measurements:|| ::: | Kit# 11-1129 has NO Spacer) | | | My Measurements:|| ::: | Kit# 11-1129 has NO Spacer) | | ||
| - | | Coil Wire Dia. | .195" | ::: | I have not actually measured any of the other kits, but if they\\ include the same spring with simply different length spacers,\\ you could buy (new or used) any of these kits & then make\\ your own PVC spacer to fit your forks | | + | | Coil Wire Dia. | .195" | ::: | I have not actually measured any of the other kits, but if they\\ include the same spring with simply different length spacers,\\ you could buy (new or used) any of these kits & then make\\ your own PVC spacer to fit your forks. | |
| | Length of Tight Winding | 4.460" | ::: | ::: | | | Length of Tight Winding | 4.460" | ::: | ::: | | ||
| | # of coils Tightly Wound | 18 | ::: | ::: | | | # of coils Tightly Wound | 18 | ::: | ::: | | ||
| - | | Length of Loose Winding | 14.040" | ::: | ::: | | + | | Length of Loose Winding | 14.040" | ::: | Since the 11-1527 kit came with 3" spacers, I had to cut them\\ down to 2" spacers to be right for my 1994 model. | |
| | # of coils Loosely Wound | 38 | ::: | ::: | | | # of coils Loosely Wound | 38 | ::: | ::: | | ||
