Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ref:susp04d [2022/12/04 03:16] ixl2relax [Installing Progessive 440 Rear Shocks on 1994 XLH] |
techtalk:ref:susp04d [2022/12/04 03:34] (current) ixl2relax |
||
---|---|---|---|
Line 3: | Line 3: | ||
\\ | \\ | ||
- | ====== Installing Progessive 440 Rear Shocks on 1994 XLH ====== | + | ====== Installing Progressive 440 Rear Shocks on 1994 XLH ====== |
The rear shocks I had with the bike were apparently from the Hugger models (1994 era) because they were only 11-3/4" long. Since they provided a rather harsh ride, I decided to upgrade those to 12-1/2" shocks, but I wasn't settled on a specific brand or model. So I began looking at a number of shocks that might fill the bill. | The rear shocks I had with the bike were apparently from the Hugger models (1994 era) because they were only 11-3/4" long. Since they provided a rather harsh ride, I decided to upgrade those to 12-1/2" shocks, but I wasn't settled on a specific brand or model. So I began looking at a number of shocks that might fill the bill. | ||
Line 46: | Line 46: | ||
| If rider + luggage weighs 250# or more, Progressive recommends \\ . . . . Rear Shock 440-4001 which has 90#/130# spring rate (Heavy Duty) | | | If rider + luggage weighs 250# or more, Progressive recommends \\ . . . . Rear Shock 440-4001 which has 90#/130# spring rate (Heavy Duty) | | ||
- | | Progressive Shock Mounting Kit# 5011-092 - Bushings, sleeves, washers, etc. $19.80 | | + | | Progressive Shock Mounting Kit# 5011-092 - Bushings, sleeves, washers, etc. | |
**The Installation:**\\ | **The Installation:**\\ | ||
Line 61: | Line 61: | ||
I wanted to set the shocks as close to the frame as possible - that would keep the stress on the bolts as close to their mounts as possible. In the end, I was actually able to mount the 440s closer to the frame than the previous shocks were mounted. I used only one spacer washer at the top and only 2 wide and 1 narrow washers at the bottom. | I wanted to set the shocks as close to the frame as possible - that would keep the stress on the bolts as close to their mounts as possible. In the end, I was actually able to mount the 440s closer to the frame than the previous shocks were mounted. I used only one spacer washer at the top and only 2 wide and 1 narrow washers at the bottom. | ||
- | All in all, not as simple a job as I hoped, but I got them fitted up nicely. | + | All in all, not as simple a job as I hoped, but I got them fitted up nicely.\\ |
+ | {{:techtalk:ref:susp:shock-prog-440-4001c-install-2.jpg?400|}}((Pic by IXL2Relax)) | ||
- | | Here's the final install picture showing them on the bike.\\ \\ \\ I finished installing them early enough in the day\\ to take them for an extended test ride. It was a\\ nice day in February and I wanted to enjoy the\\ unexpected weather opportunity.\\ \\ I put about 120 miles on the new-to-me shocks.\\ The preload was set to the minimum.\\ \\ I found them to be a definite upgrade from\\ the previous short shocks. | {{:techtalk:ref:susp:shock-prog-440-4001c-install-2.jpg?400|}}((Pic by IXL2Relax)) | | + | Here's the final install picture showing them on the bike.\\ |
+ | {{:techtalk:ref:susp:shock-prog-440-4001c-install-3.jpg?400|}}((Pic by IXL2Relax)) | ||
+ | |||
+ | I finished installing them early enough in the day to take them for an extended test ride. It was a nice day in February and I wanted to enjoy the unexpected weather opportunity. | ||
+ | |||
+ | I put about 120 miles on the new-to-me shocks. The preload was set to the minimum. I found them to be a definite upgrade from the previous short shocks. | ||