Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:svcproc20 [2020/03/02 05:38] hippysmack |
techtalk:ref:svcproc20 [2020/03/02 05:55] hippysmack [Compression Calculator] |
||
---|---|---|---|
Line 93: | Line 93: | ||
====== Compression Calculator ====== | ====== Compression Calculator ====== | ||
+ | Article by aswracing of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1441757)) and Hammer Performance site. (( http://hammerperf.com/ttcompression.shtml)) \\ | ||
+ | |||
+ | [[http://hammerperf.com/ttcompression.shtml|Click here to download a free copy of the HAMMER PERFORMANCE Compression Calculator]]. \\ | ||
So how much compression can you run with what cams, and still be able to run pump gas? \\ | So how much compression can you run with what cams, and still be able to run pump gas? \\ | ||
Line 114: | Line 117: | ||
To solve the problem, you need to dust off your trigonometry textbook and make right triangles out of it. \\ | To solve the problem, you need to dust off your trigonometry textbook and make right triangles out of it. \\ | ||
- | Or, you could take the easy way and [[http://hammerperf.com/ttcompression.shtml|click here to download a free copy of the HAMMER PERFORMANCE Compression Calculator]]. \\ | + | Or, you could take the easy way and just download the calculator. \\ |
Store the file somewhere on your hard drive where it's easy to find, and then double click on it to execute. \\ | Store the file somewhere on your hard drive where it's easy to find, and then double click on it to execute. \\ | ||
- | |||
The program is very easy to use, and it will give progressively more info as you enter more data: \\ | The program is very easy to use, and it will give progressively more info as you enter more data: \\ | ||
* For just displacement, enter the bore and stroke. | * For just displacement, enter the bore and stroke. | ||
Line 134: | Line 136: | ||
With good chamber turbulence and dual plugs, you can even run it higher, up to 9.5:1 is not unusual. \\ | With good chamber turbulence and dual plugs, you can even run it higher, up to 9.5:1 is not unusual. \\ | ||
- | This is a free tool, independently developed in-house by aswracing of the XLForum (Hammer Performance). \\ | + | This is a free tool, independently developed in-house by Hammer Performance ((aswracing of the XLForum)). \\ |
Feel free to use it and distribute it as you please. \\ | Feel free to use it and distribute it as you please. \\ | ||
It's virus-free. \\ | It's virus-free. \\ | ||
Line 140: | Line 142: | ||
All it does is perform the calculations and give you the answer. \\ | All it does is perform the calculations and give you the answer. \\ | ||
+ | Note that results given by this program are intended as a guideline only. \\ | ||
+ | HAMMER PERFORMANCE assumes no responsibility for what you do with the information presented. \\ | ||
{{:techtalk:ref:svcproc:compression_calculator_screeenshot_1_by_aswracing.jpg?direct&400|}} ((screenshot by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1441757)) {{:techtalk:ref:svcproc:compression_calculator_screeenshot_2_by_aswracing.jpg?direct&400|}} ((screenshot by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1441757)) \\ | {{:techtalk:ref:svcproc:compression_calculator_screeenshot_1_by_aswracing.jpg?direct&400|}} ((screenshot by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1441757)) {{:techtalk:ref:svcproc:compression_calculator_screeenshot_2_by_aswracing.jpg?direct&400|}} ((screenshot by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1441757)) \\ |