Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:svcproc20 [2020/03/02 05:38]
hippysmack
techtalk:ref:svcproc20 [2020/03/02 05:55]
hippysmack [Compression Calculator]
Line 93: Line 93:
  
 ====== Compression Calculator ====== ====== Compression Calculator ======
 +Article by aswracing of the XLFORUM ((http://​xlforum.net/​forums/​showthread.php?​t=1441757)) and Hammer Performance site. (( http://​hammerperf.com/​ttcompression.shtml)) \\
 +
 +[[http://​hammerperf.com/​ttcompression.shtml|Click here to download a free copy of the HAMMER PERFORMANCE Compression Calculator]]. \\
  
 So how much compression can you run with what cams, and still be able to run pump gas? \\ So how much compression can you run with what cams, and still be able to run pump gas? \\
Line 114: Line 117:
  
 To solve the problem, you need to dust off your trigonometry textbook and make right triangles out of it. \\ To solve the problem, you need to dust off your trigonometry textbook and make right triangles out of it. \\
-Or, you could take the easy way and [[http://​hammerperf.com/​ttcompression.shtml|click here to download ​a free copy of the HAMMER PERFORMANCE Compression Calculator]]. \\+Or, you could take the easy way and just download the calculator. \\
 Store the file somewhere on your hard drive where it's easy to find, and then double click on it to execute. \\ Store the file somewhere on your hard drive where it's easy to find, and then double click on it to execute. \\
- 
 The program is very easy to use, and it will give progressively more info as you enter more data: \\ The program is very easy to use, and it will give progressively more info as you enter more data: \\
   * For just displacement,​ enter the bore and stroke.   * For just displacement,​ enter the bore and stroke.
Line 134: Line 136:
 With good chamber turbulence and dual plugs, you can even run it higher, up to 9.5:1 is not unusual. \\ With good chamber turbulence and dual plugs, you can even run it higher, up to 9.5:1 is not unusual. \\
  
-This is a free tool, independently developed in-house by aswracing of the XLForum ​(Hammer Performance). \\+This is a free tool, independently developed in-house by Hammer Performance ((aswracing of the XLForum)). \\
 Feel free to use it and distribute it as you please. \\ Feel free to use it and distribute it as you please. \\
 It's virus-free. \\ It's virus-free. \\
Line 140: Line 142:
 All it does is perform the calculations and give you the answer. \\ All it does is perform the calculations and give you the answer. \\
  
 +Note that results given by this program are intended as a guideline only. \\
 +HAMMER PERFORMANCE assumes no responsibility for what you do with the information presented. \\
  
 {{:​techtalk:​ref:​svcproc:​compression_calculator_screeenshot_1_by_aswracing.jpg?​direct&​400|}} ((screenshot by aswracing of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1441757)) {{:​techtalk:​ref:​svcproc:​compression_calculator_screeenshot_2_by_aswracing.jpg?​direct&​400|}} ((screenshot by aswracing of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1441757)) \\ {{:​techtalk:​ref:​svcproc:​compression_calculator_screeenshot_1_by_aswracing.jpg?​direct&​400|}} ((screenshot by aswracing of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1441757)) {{:​techtalk:​ref:​svcproc:​compression_calculator_screeenshot_2_by_aswracing.jpg?​direct&​400|}} ((screenshot by aswracing of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1441757)) \\