Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
techtalk:ref:svcproc30 [2019/01/09 03:45] ixl2relax [REF: Troubleshooting - 07] |
techtalk:ref:svcproc30 [2019/01/09 04:09] ixl2relax ↷ Links adapted because of a move operation |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| |Touch the probes on the same side of the switch to ensure you have \\ good contact points on the probes. Clean the area if needed.|Probe each side of the switch and the buzzer on the meter should \\ sound off thus ensuring continuity between the contacts. If not, the \\ switch is defective and has to be replaced.| | |Touch the probes on the same side of the switch to ensure you have \\ good contact points on the probes. Clean the area if needed.|Probe each side of the switch and the buzzer on the meter should \\ sound off thus ensuring continuity between the contacts. If not, the \\ switch is defective and has to be replaced.| | ||
| - | |{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_6_by_hippysmack.jpg?direct&400|}}|{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_7_by_hippysmack.jpg?direct&400|}}| | + | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_6_by_hippysmack.jpg?direct&400|}}|{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_7_by_hippysmack.jpg?direct&400|}}| |
| |This tested out to be defective with an open circuit. ((photos by Hippysmack))|| | |This tested out to be defective with an open circuit. ((photos by Hippysmack))|| | ||
| - | |{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_8_by_hippysmack.jpg?direct&400|}}|{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_9_by_hippysmack.jpg?direct&400|}}| | + | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_8_by_hippysmack.jpg?direct&400|}}|{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_9_by_hippysmack.jpg?direct&400|}}| |
| ==== Testing for the Opening / Closing Pressure ==== | ==== Testing for the Opening / Closing Pressure ==== | ||
| Line 19: | Line 19: | ||
| |The valve was placed inline in case something went wrong. ((photo by Hippysmack))| | |The valve was placed inline in case something went wrong. ((photo by Hippysmack))| | ||
| - | |{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_1_by_hippysmack.jpg?direct&400|}}| | + | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_1_by_hippysmack.jpg?direct&400|}}| |
| |With zero pressure applied, the circuit is closed, continuity is achieved \\ between the probes and the buzzer sounds off. ((photo by Hippysmack))|With 27 PSI applied, continuity is broken and the buzzer is quiet. ((photo by Hippysmack))| | |With zero pressure applied, the circuit is closed, continuity is achieved \\ between the probes and the buzzer sounds off. ((photo by Hippysmack))|With 27 PSI applied, continuity is broken and the buzzer is quiet. ((photo by Hippysmack))| | ||
| - | |{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_2_by_hippysmack.jpg?direct&400|}}|{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_3_by_hippysmack.jpg?direct&400|}}| | + | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_2_by_hippysmack.jpg?direct&400|}}|{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_3_by_hippysmack.jpg?direct&400|}}| |
| |This switch didn't make contact until the pressure got down to about 2-1/2 PSI. \\ However, this test should have been performed with a lower range gauge for tighter low end calibration. ((photos by Hippysmack))|| | |This switch didn't make contact until the pressure got down to about 2-1/2 PSI. \\ However, this test should have been performed with a lower range gauge for tighter low end calibration. ((photos by Hippysmack))|| | ||
| - | |{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_5_by_hippysmack.jpg?direct&400|}}|{{:techtalk:ref:trouble:testing_the_oil_pressure_switch_4_by_hippysmack.jpg?direct&400|}}| | + | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_5_by_hippysmack.jpg?direct&400|}}|{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_4_by_hippysmack.jpg?direct&400|}}| |
