Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools103 [2019/05/21 17:43] hippysmack |
techtalk:ref:tools103 [2019/05/26 23:29] hippysmack xlforum |
||
---|---|---|---|
Line 30: | Line 30: | ||
|{{:techtalk:ref:tools:flywheel_holding_jig_3_by_saddlebagrail.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_holding_jig_4_by_saddlebagrail.jpg?direct&300|}}| | |{{:techtalk:ref:tools:flywheel_holding_jig_3_by_saddlebagrail.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_holding_jig_4_by_saddlebagrail.jpg?direct&300|}}| | ||
+ | |||
+ | ==== Steel angle fixture ==== | ||
+ | photos by GaryanOdinson of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1715974&page=2)) | ||
+ | |{{:techtalk:ref:tools:flywheel_fixture_1_by_garyanodinson.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_fixture_2_by_garyanodinson.jpg?direct&300|}}| | ||
+ | |||
+ | |{{:techtalk:ref:tools:flywheel_fixture_3_by_garyanodinson.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_fixture_4_by_garyanodinson.jpg?direct&300|}}| | ||
+ | |||
+ | ==== Jig inserts ==== | ||
+ | photos by Iron73 of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1715974&page=2)) \\ | ||
+ | |||
+ | |{{:techtalk:ref:tools:flywheel_jig_inserts_1_by_iron73.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_jig_inserts_2_by_iron73.jpg?direct&300|}}|{{:techtalk:ref:tools:flywheel_jig_inserts_3_by_iron73.jpg?direct&300|}}| | ||
===== Installing / Removing Timken Bearings ===== | ===== Installing / Removing Timken Bearings ===== | ||
Line 68: | Line 79: | ||
|Here is another way to true flywheels in a small Myford lathe that has only a 4.5" swing that won't fit Harley flywheels. \\ Two offset pieces made from some flat half-inch thick bar and some half-inch round bar.||| | |Here is another way to true flywheels in a small Myford lathe that has only a 4.5" swing that won't fit Harley flywheels. \\ Two offset pieces made from some flat half-inch thick bar and some half-inch round bar.||| | ||
^ **Truing flywheels on center in a lathe via offset jigs** ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) ^^^ | ^ **Truing flywheels on center in a lathe via offset jigs** ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) ^^^ | ||
+ | |||
+ | |{{:techtalk:ref:tools:truing_flywheels_in_a_lathe_by_aussiegazz.jpg?direct&300|}}| | ||
+ | ^ **Truing flywheels on center in a lathe with \\ no offset jigs** ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=9)) ^ | ||
+ | |||
===== Crankshaft / Flywheel Installation ===== | ===== Crankshaft / Flywheel Installation ===== | ||