Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:tools107 [2019/10/19 04:33]
hippysmack [Bushing Installation]
techtalk:ref:tools107 [2019/10/19 04:41]
hippysmack [Bushing Removal]
Line 28: Line 28:
 |{{:​techtalk:​ref:​tools:​pilot_bearing_puller_2_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_3_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_by_decman.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​pilot_bearing_puller_2_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_3_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_by_decman.jpg?​direct&​300|}}|
  
-Homemade bushing remover: \\ +**Homemade bushing remover**: \\ 
-The puller is made from 1" ID black pipe and 1/​2"​-13 threaded rod. \\ +The puller is made from 1" ID black pipe and 1/​2"​-13 threaded rod. You tap the flex head-puller head through the cam bearing. \\ 
-The little nub puller with a collar that you knock into the bearing is made from 3/4" rod. \\+The little nub puller with a collar that you knock into the bearing is made from 3/4" rod. Then screw the rod into the head to tighten the jaws. \\ 
 +Then place the collar over the rod and nut to start the pulling. \\ 
 4 grooves were cut into the end for flex / compression to push through the bearing. \\ 4 grooves were cut into the end for flex / compression to push through the bearing. \\
-You simply tap the flex head-puller through ​the bearing. \\+Then it was center drilled 7/16" and tapped 1/2"-13 and the slots were cut with a 3/16" end mill. \\
 The threaded rod causes outward pressure on the jaws of the head when pulled. \\ The threaded rod causes outward pressure on the jaws of the head when pulled. \\
 |{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_1_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_2_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_4_by_fergerburger.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_1_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_2_by_fergerburger.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_4_by_fergerburger.jpg?​direct&​300|}}|
Line 44: Line 46:
 The knocker rod is made from 1" aluminum bar stock with a .030" shoulder to recess into the bearing, .030" into the case. ((fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1349714)) \\ The knocker rod is made from 1" aluminum bar stock with a .030" shoulder to recess into the bearing, .030" into the case. ((fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1349714)) \\
  
-The compression plate is made from a scrap steel plate. The bolts screw in push the bushings in place. ​((See the build pics below by Hippysmack)) \\+The compression plate is made from a scrap steel plate. The bolts screw in to push the bushings in place. See the [[techtalk:​ref:​tools107#​reverse_engineered_cam_bushing_installer|build pics]] below by Hippysmack\\
  
 {{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_3_by_fergerburger.jpg?​direct&​300|}} ((photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1349714)) {{techtalk:​ref:​tools:​cam_bushing_installer_41_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) {{techtalk:​ref:​tools:​cam_bushing_installer_39_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) ​ {{:​techtalk:​ref:​tools:​homemade_cam_bushing_tools_3_by_fergerburger.jpg?​direct&​300|}} ((photo by fergerburger of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1349714)) {{techtalk:​ref:​tools:​cam_bushing_installer_41_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) {{techtalk:​ref:​tools:​cam_bushing_installer_39_by_hippysmack.jpg?​direct&​300|}} ((photo by Hippysmack)) ​