Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
techtalk:ref:tools113 [2018/05/20 06:09] ixl2relax [REF: Shop Notes, Tips, and Tools - Sub-03M] |
techtalk:ref:tools113 [2024/01/23 04:15] (current) hippysmack |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | ====== REF: Tools - Sub-013 ====== | + | ====== REF: Tools - 113 ====== |
| ====== Wheel Truing / Balancing ====== | ====== Wheel Truing / Balancing ====== | ||
| - | |{{:techtalk:ref:notes:wheel_truing_stand_1_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:notes:wheel_truing_stand_2_by_hopper.jpg?direct&300|}}| | + | |{{techtalk:ref:tools:wheel_truing_stand_1_by_hopper.jpg?direct&300|}}|{{techtalk:ref:tools:wheel_truing_stand_2_by_hopper.jpg?direct&300|}}| |
| - | | $5 wheel truing stand ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) | For balancing, use old worn wheel bearings, not \\ notchy, with WD40 for lube. Nice free movement. ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) | | + | | $5 wheel truing stand ((photo by Hopper of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools?t=395586)) | For balancing, use old worn wheel bearings, not \\ notchy, with WD40 for lube. Nice free movement. ((photo by Hopper of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools?t=395586)) | |
| - | |{{:techtalk:ref:notes:wheel_truing_3_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:notes:wheel_truing_4_by_hopper.jpg?direct&300|}}| | + | |{{techtalk:ref:tools:wheel_truing_3_by_hopper.jpg?direct&300|}}|{{techtalk:ref:tools:wheel_truing_4_by_hopper.jpg?direct&300|}}| |
| - | |For lacing: To get the initial spoking nice and centered, drill a hole on your work bench for the axle, \\ scribe a circle where the rim goes and locate it with wooden blocks screwed to the bench. \\ Wooden shims provide the correct offset. ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))|| | + | |For lacing: To get the initial spoking nice and centered, drill a hole on your work bench for the axle, \\ scribe a circle where the rim goes and locate it with wooden blocks screwed to the bench. \\ Wooden shims provide the correct offset. ((photo by Hopper of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools?t=395586))|| |
