Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools117 [2018/05/16 23:42] hippysmack [Mainshaft Bearing Press] |
techtalk:ref:tools117 [2020/08/11 04:49] hippysmack [Retaining Ring Removal] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | ====== REF: Shop Notes, Tips, and Tools - Sub-03Q ====== | + | ====== REF: Tools - 117 ====== |
| ====== Mainshaft ====== | ====== Mainshaft ====== | ||
| ===== Mainshaft Bearing Press ===== | ===== Mainshaft Bearing Press ===== | ||
| - | |{{techtalk:ref:notes:mainshaft_press_by_sc72.jpg?direct&300|}}| | + | |{{techtalk:ref:tools:mainshaft_press_by_sc72.jpg?direct&300|}}| |
| - | |Mainshaft Bearing Press ((photo by sc72 http://xlforum.net/forums/showthread.php?t=1717592&highlight=engine+sprocket&page=16))| | + | ^Mainshaft Bearing Press ((photo by sc72 http://xlforum.net/forums/showthread.php?t=1717592&highlight=engine+sprocket&page=16))^ |
| ====== Countershaft ====== | ====== Countershaft ====== | ||
| + | |||
| + | |This is a mock setup for checking countershaft endplay. The bent wire is used to push and pull on the countershaft. You can read the endplay directly from the dial \\ indicator which is mounted on the alloy spacer with the bolt through it. The bolt screws into the bottom tranny case mount hole on the left case half with the tranny \\ sitting correctly in the engine.||| | ||
| + | |{{techtalk:ref:svcproc:countershaft_endplay_1_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:svcproc:countershaft_endplay_2_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:svcproc:countershaft_endplay_3_by_ferrous_head.jpg?direct&300|}}| | ||
| + | ^ Dial Indicator for checking Countershaft Endplay ((Photos and article by Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=6)) ^^^ | ||
| + | |||
| + | |||
| + | ===== Countershaft Low Gear Bushing Installation ===== | ||
| + | |||
| + | * Found out the hard way not to hand ream this bushing after fitting. Set it up in a lathe and bore it true with a steel ring to hold the gear in the lathe. \\ The 17 tooth gear won't sit in a three jaw chuck evenly. ((Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) | ||
| + | |||
| + | |{{techtalk:ref:tools:first_gear_bushing_installation_tool_1_by_hopper.jpg?direct&400|}}|{{techtalk:ref:tools:bushing_installation_tool_by_hopper.jpg?direct&400|}}| | ||
| + | ^Countershaft low gear bushing jig for use in a 3 jaw chuck lathe ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))^A pair of sockets and a 3/8" bolt for extraction, \\ a stepped collar on a 9/16 bolt to install. ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))^ | ||
| + | |||
| + | |||
| ===== Transmission Countershaft Needle Roller Bearing Drift ===== | ===== Transmission Countershaft Needle Roller Bearing Drift ===== | ||
| Line 18: | Line 32: | ||
| * Like all bearings, they can be changed cold but all you are doing is tearing the hell out of the aluminium and setting it up for the bearing to spin the housing due to the resulting loose fit, specially if the job has been done once or twice before. | * Like all bearings, they can be changed cold but all you are doing is tearing the hell out of the aluminium and setting it up for the bearing to spin the housing due to the resulting loose fit, specially if the job has been done once or twice before. | ||
| - | |Drift for the transmission countershaft \\ needle roller bearings ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))| | ||
| - | |{{:techtalk:ref:notes:transmission_countershaft_needle_roller_bearings_drift_by_hopper.jpg?direct&300|}}| | ||
| + | |{{techtalk:ref:tools:transmission_countershaft_needle_roller_bearings_drift_by_hopper.jpg?direct&300|}}| | ||
| + | ^Drift for the transmission countershaft \\ needle roller bearings ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))^ | ||
| + | |||
| + | ===== Retaining Ring Removal ===== | ||
| + | |{{:techtalk:ref:tools:retaining_ring_pliers_1_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ref:tools:retaining_ring_pliers_2_by_dr_dick.jpg?direct&300|}}| | ||
| + | | Retaining ring pliers ((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1257259)) || | ||
| + | |||
| + | |{{:techtalk:ref:tools:piston_ring_spreader_for_trans_retaining_rings_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:piston_ring_spreader_for_trans_retaining_rings_1_by_hippysmack.jpg?direct&300|}}| | ||
| + | | Piston ring pliers ((photos by Hippysmack)) || | ||
| \\ | \\ | ||
