Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools117 [2018/05/22 18:54] hippysmack [Transmission Countershaft Needle Roller Bearing Drift] |
techtalk:ref:tools117 [2019/02/15 11:17] hippysmack [Retaining Ring Removal] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| |This is a mock setup for checking countershaft endplay. The bent wire is used to push and pull on the countershaft. You can read the endplay directly from the dial \\ indicator which is mounted on the alloy spacer with the bolt through it. The bolt screws into the bottom tranny case mount hole on the left case half with the tranny \\ sitting correctly in the engine.||| | |This is a mock setup for checking countershaft endplay. The bent wire is used to push and pull on the countershaft. You can read the endplay directly from the dial \\ indicator which is mounted on the alloy spacer with the bolt through it. The bolt screws into the bottom tranny case mount hole on the left case half with the tranny \\ sitting correctly in the engine.||| | ||
| - | |{{techtalk:ref:notes:countershaft_endplay_1_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:notes:countershaft_endplay_2_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:notes:countershaft_endplay_3_by_ferrous_head.jpg?direct&300|}}| | + | |{{techtalk:ref:svcproc:countershaft_endplay_1_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:svcproc:countershaft_endplay_2_by_ferrous_head.jpg?direct&300|}}|{{techtalk:ref:svcproc:countershaft_endplay_3_by_ferrous_head.jpg?direct&300|}}| |
| ^ Dial Indicator for checking Countershaft Endplay ((Photos and article by Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=6)) ^^^ | ^ Dial Indicator for checking Countershaft Endplay ((Photos and article by Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=6)) ^^^ | ||
| Line 35: | Line 35: | ||
| |{{techtalk:ref:tools:transmission_countershaft_needle_roller_bearings_drift_by_hopper.jpg?direct&300|}}| | |{{techtalk:ref:tools:transmission_countershaft_needle_roller_bearings_drift_by_hopper.jpg?direct&300|}}| | ||
| ^Drift for the transmission countershaft \\ needle roller bearings ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))^ | ^Drift for the transmission countershaft \\ needle roller bearings ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))^ | ||
| + | |||
| + | ===== Retaining Ring Removal ===== | ||
| + | |{{:techtalk:ref:tools:retaining_ring_pliers_1_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ref:tools:retaining_ring_pliers_2_by_dr_dick.jpg?direct&300|}}| | ||
| + | | Retaining ring pliers ((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1257259)) || | ||
| + | |||
| + | |{{:techtalk:ref:tools:piston_ring_spreader_for_trans_retaining_rings_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:piston_ring_spreader_for_trans_retaining_rings_1_by_hippysmack.jpg?direct&300|}}| | ||
| + | | Piston ring pliers ((photos by Hippysmack)) || | ||
| \\ | \\ | ||
