[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: Tools - 131 ======
====== Trans Final Drive Sprocket Tools ======

====== Sprocket Nut Removal ======
Transmission sprocket nut for rigid XLs should all be the same wrench size: 1-7/8" (47.625mm) . \\
It's a 6 point nut and will require a 6 point socket to remove / install. \\
Normally, the sprocket holding tool below is used to keep the sprocket from turning while removing the nut. \\
 
{{:techtalk:ref:tools:transmission_sprocket_removal_with_impact_wrench_by_anachris.jpg?direct&300|}} ((photo by AnaChris of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/160818-1250-build-bottom-to-top/page20?t=1725973&highlight=oil+pump&page=20)) {{:techtalk:ref:tools:transmission_sprocket_nut_size_1998_1200s_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\

====== Sprocket Holding Tool ======
Final drive locking tool from J&Pcycles.com part # (910-576). \\
Don't forget to buy a longer grade 8 bolt to use as a stop for the tool. \\
Just pick the hole your going to use and but one from an auto parts or hardware store. \\

{{:techtalk:ref:tools:trans_sprocket_holding_tool_by_anachris.jpg?direct&300|}} ((photo by AnaChris of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/160818-1250-build-bottom-to-top/page30?t=1725973&highlight=oil+pump&page=30)) \\


DIY by Graywolf of the XLForum - See thread here: https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-general-discussion-and-problems/168260-final-drive-pulley-tool-12-50-usd?t=1806002

{{:techtalk:ref:tools:trans-finaldrivesprocket-tool-graywolf.jpg?400|}}((photo by Graywolf of the XLForum https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-general-discussion-and-problems/168260-final-drive-pulley-tool-12-50-usd?t=1806002))

===== Fabricated Sprocket Nut Wrench =====
|{{:techtalk:ref:tools:transmission_sprocket_nut_1_by_krtt_clone.jpg?direct&300|}}|{{:techtalk:ref:tools:transmission_sprocket_nut_2_by_krtt_clone.jpg?direct&300|}}|
|  Built Sprocket Nut Socket ((photos by KRTT Clone of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools/page5?t=395586&page=5))  ||

|{{:techtalk:ref:tools:transmission_sprocket_nut_3_by_krtt_clone.jpg?direct&300|}}|{{:techtalk:ref:tools:transmission_sprocket_nut_4_by_krtt_clone.jpg?direct&300|}}|{{:techtalk:ref:tools:transmission_sprocket_nut_5_by_krtt_clone.jpg?direct&300|}}|
|  Built Sprocket Nut Socket ((photos by KRTT Clone of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools/page5?t=395586&page=5))  |||

|{{:techtalk:ref:tools:transmission_sprocket_nut_6_by_krtt_clone.jpg?direct&300|}}|{{:techtalk:ref:tools:transmission_sprocket_nut_7_by_krtt_clone.jpg?direct&300|}}|{{:techtalk:ref:tools:transmission_sprocket_nut_8_by_krtt_clone.jpg?direct&300|}}|
|  Built Sprocket Nut Socket ((photos by KRTT Clone of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/63858-special-tools/page5?t=395586&page=5))  |||


\\

[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]