Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
techtalk:ref:tools145 [2019/12/21 01:57]
hippysmack [Oil Pump Check Ball Seat Lapping Tool]
techtalk:ref:tools145 [2024/01/24 21:47] (current)
hippysmack
Line 10: Line 10:
  
 ===== Oil Pump Check Ball Seat Lapping Tool ====== ===== Oil Pump Check Ball Seat Lapping Tool ======
- +**Homemade check ball lapping tool**: \\ 
-**The tool on the left** is a homemade check ball lapping tool used to lap the seat where the check ball sits in the oil pump (57-76). ((Toolmaker of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=499487&​highlight=check+ball+lapping+tool)) \\+The tool on the left is a homemade check ball lapping tool used to lap the seat where the check ball sits in the oil pump (57-76). ((Toolmaker of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​72481-i-m-sick-and-tired-of-wet-sumping?​t=499487&​highlight=check+ball+lapping+tool)) \\
 It's made with a tool steel shank and a 3/8" carbide ball tip on the end. \\ It's made with a tool steel shank and a 3/8" carbide ball tip on the end. \\
 The pocket for the ball to sit was cut with a 3/8" ball end mill then a few drops of Loctite 404 to keep it there. \\ The pocket for the ball to sit was cut with a 3/8" ball end mill then a few drops of Loctite 404 to keep it there. \\
  
-**The tool in the middle** is a check-ball seat burnishing set. ((DaWind of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=1013445&​page=2)) \\+**Check ball seat burnishing tool**: \\ 
 +The tool in the middle is a check-ball seat burnishing set. ((DaWind of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​109149-oil-pump-check-ball-seating/​page2?​t=1013445&​page=2)) \\
 The idea is to turn the ball into the seat several times, thereby smoothing it to a very fine finish. \\ The idea is to turn the ball into the seat several times, thereby smoothing it to a very fine finish. \\
 It works quite well with these old check valve seats, but you can and do use quite a bit of force with the cast iron for a good result. \\ It works quite well with these old check valve seats, but you can and do use quite a bit of force with the cast iron for a good result. \\
Line 27: Line 28:
 Then, hold the whole mess in tension between centers as you soldered. They surely have to be straight or they aren’t much use. \\ Then, hold the whole mess in tension between centers as you soldered. They surely have to be straight or they aren’t much use. \\
  
-**The tool on the right** was made as a check ball tester and oil pump prelube tool. \\ +**Check ball tester and oil pump prelube tool**: \\ 
-With this tool, all you have to do is use a grease gun (without grease) filled with oil and pump it into the system so a dry start can be avoided. ((bustert of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=1813185&​page=2)) \\+The tool on the right was made as a check ball tester and oil pump prelube tool. \\ 
 +With this tool, all you have to do is use a grease gun (without grease) filled with oil and pump it into the system so a dry start can be avoided. ((bustert of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​168986-oil-pump-check-fixes/​page2?​t=1813185&​page=2)) \\
  
 |{{:​techtalk:​ref:​tools:​homemade_check_ball_lapping_tool_by_toolmaker.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​oil_pump_check_ball_lap_by_dawind.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​check_ball_tester_and_prelube_fitting_by_bustert.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​homemade_check_ball_lapping_tool_by_toolmaker.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​oil_pump_check_ball_lap_by_dawind.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​check_ball_tester_and_prelube_fitting_by_bustert.jpg?​direct&​300|}}|
-|  Homemade check ball lapping tool ((photo by Toolmaker of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=499487&​highlight=check+ball+lapping+tool)) ​ |  Check-ball seat burnishing set ((photo by DaWind of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=1013445&​page=2)) ​ |   Oil pump check valve tester / pump prelube tool. ((photo by bustert of the XLFORUM ​http://​xlforum.net/​forums/showthread.php?​t=1813185&​page=2)) ​ | +|  Homemade check ball lapping tool ((photo by Toolmaker of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​72481-i-m-sick-and-tired-of-wet-sumping?​t=499487&​highlight=check+ball+lapping+tool)) ​ |  Check-ball seat burnishing set ((photo by DaWind of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​109149-oil-pump-check-ball-seating/​page2?​t=1013445&​page=2)) ​ |   Oil pump check valve tester / pump prelube tool. ((photo by bustert of the XLFORUM ​https://www.xlforum.net/​forum/sportster-motorcycle-forum/​sportster-motorcycle-era-specific-and-model-specific/​ironhead-sportster-motorcycle-talk-1957-1985/​168986-oil-pump-check-fixes/​page2?​t=1813185&​page=2)) ​ |
- +
  
 ====== 77 and later oil pumps ====== ====== 77 and later oil pumps ======
Line 50: Line 50:
  
 |{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_1_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_2_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_3_by_hippysmack.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_1_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_2_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_3_by_hippysmack.jpg?​direct&​300|}}|
- 
  
 |{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_4_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_5_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_6_by_hippysmack.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_4_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_5_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​precision_cuticle_scissors_6_by_hippysmack.jpg?​direct&​300|}}|
  
 ====== Oil Pump Removal ====== ====== Oil Pump Removal ======
- 
 Mounting bolts (to the engine): \\ Mounting bolts (to the engine): \\
 77-97 models - (4 bolts) \\ 77-97 models - (4 bolts) \\