Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:tools168 [2019/09/11 05:34] hippysmack [REF: Tools - 167] |
techtalk:ref:tools168 [2023/11/04 19:02] hippysmack created |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| ====== REF: Tools - 168 ====== | ====== REF: Tools - 168 ====== | ||
| - | ====== Dremil Type Rotary Tool ====== | + | ====== Bulb Type Pressure Tester ====== |
| - | A Dremil tool has many uses from cutting to polishing metal. Always wear a face shield when using this tool. \\ | + | Below is a bulb type pressure tester for testing the carburetor needle seat valve as referenced in TSB #564. \\ |
| - | It operates at a very high speed and tiny pieces of the cutting bits and the metal will hit your eyes faster than you can blink. \\ | + | It's for use in testing the seat valve of Tillotson carburetors used on 1966-later Sportsters and 1967-later Electra Glides. \\ |
| - | It's good for cutting carbon & stainless steel, shortening bolts, shaping metal projects etc. \\ | + | [[techtalk:miscres:miscres05#tsb_550-599|Click Here]] to go to the TSB page, scroll down and click on the "Y" next to TSB #564 to download the bulletin. \\ |
| + | The bulletin was an attempt by the MoCo to diagnose a simple needle/seat issue and replace if needed at the dealer level. \\ | ||
| + | (instead of sending the carb back to the factory for a warranty claim) \\ | ||
| - | {{:techtalk:ref:tools:dremel_tool_by_graywolf.jpg?direct&300|}} ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3)) \\ | + | This bulb tester is HD (94750-68). \\ |
| - | + | Per the service bulletin. it's installed on the fuel inlet fitting with the vent plugged. \\ | |
| - | ====== Uses ====== | + | Squeezing the bulb adds pressure to the inlet and the gauge shows how much is added. \\ |
| - | + | A moistened needle and seat should hold app. 1 to 1·1/2 psi and release at approximately 3 to 5 psi. \\ | |
| - | |Cutting slots in pipes for shields. ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3))| Shortening a bolt. ((photos by Hippysmack)) || | + | A dry needle and seat will not hold as well as a moist one. \\ |
| - | |{{:techtalk:ref:tools:heatshield_strap_by_graywolf.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_2_by_hippysmack.jpg?direct&300|}}| | + | |
| - | | | + | |
| + | Here is the bulb tester. Click on any pic to enlarge: \\ | ||
| + | | HD Needle-Seat Bulb-Type Leak Tester (94750-68) ((photos courtesy of Ebay seller; cdchoppa. [[https://www.ebay.com/str/cdchoppa?_trksid=p4429486.m145687.l149086|Link to Ebay Store]] )) ||| | ||
| + | |{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic1_by_cdchoppa.jpg?direct&300|}}|{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic2_by_cdchoppa.jpg?direct&300|}}|{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic3_by_cdchoppa.jpg?direct&300|}}| | ||
| \\ | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
| - | |||
