Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools170 [2020/08/28 05:11] hippysmack [Please Use Proper Safety Precautions] |
techtalk:ref:tools170 [2020/08/28 06:28] hippysmack [Angle Grinder vs Die Grinder] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| ====== REF: Tools - 170 ====== | ====== REF: Tools - 170 ====== | ||
| - | ====== Hand Held Grinder / Cutter ====== | + | ====== Hand Held Grinder / Cutter / Dremil ====== |
| \\ | \\ | ||
| Line 39: | Line 39: | ||
| The main differences between an angle grinder and a die grinder are the design of the tool, size, and power. \\ | The main differences between an angle grinder and a die grinder are the design of the tool, size, and power. \\ | ||
| An angle grinder is primarily used for cutting and rough grinding, whereas the die grinder is a rotary tool used for precision work. \\ | An angle grinder is primarily used for cutting and rough grinding, whereas the die grinder is a rotary tool used for precision work. \\ | ||
| - | Here is a comparison chart between the two grinders. ((https://www.finepowertools.com/grinders/die-grinder-vs-angle-grinder/)) \\ | ||
| - | |||
| - | |Tool|Design|Size|Power Source|Speed|Power|Best for| | ||
| - | |Angle Grinder|Heavy-duty \\ power tool|Generally larger|Electric (corded) \\ Battery (cordless)|6500 – 20000 RPM|1.5-5 HP|Rough grinding, cutting| | ||
| - | |Die Grinder|Rotary tool|Generally smaller|Compressed air \\ Battery|15000 – 30000 RPM|Less than 1 HP|Precision cutting / grinding| | ||
| Line 52: | Line 47: | ||
| ====== Die Grinder ====== | ====== Die Grinder ====== | ||
| - | {{:techtalk:ref:tools:die_grinder_1_by_dk_custom.jpg?direct&300|}} ((photo by DK Custom of the XLFORUM http://xlforum.net/forums/showthread.php?t=1582019&page=6)) {{:techtalk:ref:tools:die_grinder_2_by_dk_custom.jpg?direct&300|}} ((photo by DK Custom of the XLFORUM http://xlforum.net/forums/showthread.php?t=1582019&page=6)) \\ | + | | Custom fender fitting. ((photos by DK Custom of the XLFORUM http://xlforum.net/forums/showthread.php?t=1582019&page=6)) || |
| + | |{{:techtalk:ref:tools:die_grinder_1_by_dk_custom.jpg?direct&300|}}|{{:techtalk:ref:tools:die_grinder_2_by_dk_custom.jpg?direct&300|}}| | ||
| + | |||
| + | ====== Dremil Rotary Tool ====== | ||
| + | ====== Dremil Type Rotary Tool ====== | ||
| + | A Dremil tool has many uses from cutting to polishing metal. Always wear a face shield when using this tool. \\ | ||
| + | It operates at a very high speed and tiny pieces of the cutting bits and the metal will hit your eyes faster than you can blink. \\ | ||
| + | It's good for cutting carbon & stainless steel, shortening bolts, shaping metal, polishing etc. \\ | ||
| + | |||
| + | | Dremil tool. ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3)) | Cutting slots in pipes for shields. ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3)) | | ||
| + | |{{:techtalk:ref:tools:dremel_tool_by_graywolf.jpg?direct&300|}}|{{:techtalk:ref:tools:heatshield_strap_by_graywolf.jpg?direct&300|}}| | ||
| + | |||
| + | Usually, cutting the end off a bolt requires sanding / filing the cut area to deburr / chamfer the end. \\ | ||
| + | However, the Dremil tool cuts at a high speed with a thin cutting disc. \\ | ||
| + | Keep the cutting blade perpendicular to the threads while cutting and, most of the time, deburring the cut end is optional or at least minimal. \\ | ||
| + | There is no need to install a nut and back it off the threads as you would normally do when using a hack saw or grinder. \\ | ||
| + | |||
| + | | Shortening a bolt. ((photos by Hippysmack)) ||| | ||
| + | |{{:techtalk:ref:tools:shortening_a_bolt_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_3_by_hippysmack.jpg?direct&300|}}| | ||
| \\ | \\ | ||
