REF: Tools - 172 - Sportsterpedia

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: Tools - 172 ======
====== Lifters ======
See also [[techtalk:ref:svcproc16|Hydraulic Lifter - Disassembly / Inspection / Assembly]] in the EVO section of the Sportsterpedia. \\

There is a small amount of pressure on the hydraulic lifter plunger holding the top retainer clip in place on a dry lifter. \\
It can be pushed down with your finger to install the clip. \\
But with a lifter half or more full of oil, it's harder to work the plunger with your fingers as the pressure behind the plunger is greater. \\
If you install the lifter into a holder, that frees up both hands and gives better leverage on the plunger. \\
The holder below is fabbed from a steel sheet and a welded bushing to hold the lifter. \\
A 2x4 block of wood with a 1" hole drilled into it can also be used to hold the lifter. \\

Below is a fabbed steel holder. \\
The block is used to press the plunger down. A spare pushrod or screwdriver can also be used to depress the plunger. \\

{{:techtalk:ref:tools:lifter_holding_tool_1_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_2_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_3_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) \\

{{:techtalk:ref:tools:lifter_holding_tool_4_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_5_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_6_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) \\

----

A doglegged pick works good for removing the retainer clip and removing the internals. A small flat head screwdriver works also. \\
Push slightly on the plunger to remove pressure on the clip and use the pic to pull the clip away from the groove in the top. \\

{{:techtalk:ref:svcproc:lifter_disassembly_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\

{{:techtalk:ref:svcproc:lifter_disassembly_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_14_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\


----

If you just need to store lifters temporarily for a quick removal / installation and have a pegboard, you can use a couple pegs as a holder for lifters. \\
The two legged pegs with a cut piece of gas tubing to snug against the lifters works well. \\
Then simply cover them with a rag or towel awaiting an oil soak and installation. \\

{{:techtalk:ref:tools:temp_lifter_holders_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:temp_lifter_holders_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\


\\

[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]
Trace: • IH: Electrical System • REF: Tools - 166 • REF: Tools - 172 • REF: Gears, Sprockets, Belts - Sub-01A • REF: Tools - 157 • REF: Tools - 145
Navigation

Search

Toolbox
