Differences
This shows you the differences between two versions of the page.
techtalk:ref:transfinal02 [2019/11/28 23:02] hippysmack created |
techtalk:ref:transfinal02 [2019/11/28 23:29] (current) hippysmack [Homemade Drive Belt Tensioner] |
||
---|---|---|---|
Line 3: | Line 3: | ||
\\ | \\ | ||
====== Homemade Drive Belt Tensioner ====== | ====== Homemade Drive Belt Tensioner ====== | ||
+ | {{:techtalk:ref:transfinal:diy_belt_tensioner_10_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) \\ | ||
+ | This mod was actually done to install 15" shocks on a 2013 Iron 883. \\ | ||
+ | As a result of the taller shocks, the belt was loose due to the new geometry and was just barely rubbing on the exhaust bracket. \\ | ||
+ | In search of a belt tensioner, Free Spirits makes a top quality one but it is expensive and uses the same mounts as an RSD exhaust. \\ | ||
+ | So the homemade one below was done using a Dorman (419-109) belt tensioner for cars ($20 on Amazon). \\ | ||
+ | It seemed to be solidly built and has a very sturdy spring. The only downfall is that the idler pulley is plastic but it doesn't need to be all that strong. \\ | ||
+ | The bracket was made from about a 4" piece of 1-1/2" angle iron (12 gauge). \\ | ||
+ | The tensioner and mounting holes were traced out on the angle, holes center punched and drilled to fit 3/8" socket head bolts. \\ | ||
+ | The corners were ground then smoothed with a sanding flap disk on an angle grinder. \\ | ||
+ | {{:techtalk:ref:transfinal:diy_belt_tensioner_1_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_2_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_3_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) \\ | ||
+ | {{:techtalk:ref:transfinal:diy_belt_tensioner_4_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_5_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_6_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) \\ | ||
+ | |||
+ | A suitable spot was found for mounting the assembly to the RSD exhaust mounting bracket. \\ | ||
+ | The mounting holes were marked and drilled on the exhaust bracket the same way as done on the angle iron. \\ | ||
+ | Slight shortening and final shaping was done on the angle iron on the exhaust bracket side before painting the bracket. \\ | ||
+ | |||
+ | {{:techtalk:ref:transfinal:diy_belt_tensioner_7_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_8_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) {{:techtalk:ref:transfinal:diy_belt_tensioner_9_by_chris_b_owens.jpg?direct&300|}} ((photo by chris_b_owens of the XLFORUM http://xlforum.net/forums/showthread.php?t=1919900)) \\ | ||
\\ | \\ | ||
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |