Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
techtalk:ref:wheels03 [2019/04/22 02:35]
hippysmack [Sub-Documents]
techtalk:ref:wheels03 [2020/06/24 23:29] (current)
hippysmack [Testing Your Brake Fluid]
Line 1: Line 1:
 [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]] [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]]
 ====== REF: Wheels, Brakes & Tires ====== ====== REF: Wheels, Brakes & Tires ======
 +\\
  
- +====== Brake Fluid ====== 
-====== Brake System ​====== +===== HD Recommendations ​=====
- +
-  * Brake caliper mounting bolt O-rings- Dow Corning 44 grease ("Pin Lube" in parts kit) ((1998 HD XLH FSM)) +
-  * O.D. of brake caliper piston (including chamfer), caliper piston bore and I.D. of the installed piston seal - Novaguard silicon grease. +
-  * I.D. of upper caliper (threaded) bushing bore, O.D. of threaded bushing, I.D. of upper and lower caliper mounting pin bores - Dow Corning 44 grease ("Pin Lube" in parts kit) ((1998 HD XLH FSM)) +
- +
-===== Aftermarket Brake Parts ===== +
- +
-**Aftermarket brakes vs OEM brakes** +
-Check fitment of aftermarket brakes before using them. Just because they are published as 'will fit your vehicle'​ doesn'​t make it so. The pics below are a comparison of OEM brakes and an aftermarket brand: +
- +
-|{{:​techtalk:​evo:​wheels:​brake_comparison_1_by_hippysmack.jpg?​direct&​300|}}|{{:​techtalk:​evo:​wheels:​brake_comparison_2_by_hippysmack.jpg?​direct&​300|}}| +
-|These 2 different brand of brakes look very similar. ((photo by hippysmack))|The OEM pad on right has sharper contours ((photo by hippysmack))| +
- +
-The light colored OEM brake has sharper contours to match up to the screw mounting bracket shims it rides against. The aftermarket brand is slightly shorter in length than OEM which allows it to wiggle around a bit since it doesn'​t fit tight against the screw shims which can allow it to drop below the disc resulting in poor pad wear and possible disc wear or disc drag as in the pic below: +
-|{{:​techtalk:​evo:​wheels:​brake_pad_damage_by_hippysmack.jpg?​direct&​300|}} ((photo by hippysmack))| +
- +
-Be sure your brakes can not wiggle around before installing the caliper. +
- +
- +
- +
-===== Brake Fluid ===== +
-==== HD Recommendations ====+
 ^Year Model^Hydraulic brake fluid Type^ ^Year Model^Hydraulic brake fluid Type^
 |1959 to prior to Sept. 1976 production models|DOT 3 ((Clymer Repair Manual for Sportsters 1959-1985 pg 83))|  |1959 to prior to Sept. 1976 production models|DOT 3 ((Clymer Repair Manual for Sportsters 1959-1985 pg 83))| 
Line 31: Line 10:
 |2007 and later|DOT 4 ((http://​sportsterpedia.com/​doku.php/​sportster_history:​start#​sportster_parts_chart))| |2007 and later|DOT 4 ((http://​sportsterpedia.com/​doku.php/​sportster_history:​start#​sportster_parts_chart))|
  
-==== When to Check or Change Brake Fluid ====+===== When to Check or Change Brake Fluid =====
 Copper content is the most destructive aspect of brake fluid breakdown. \\ So even without moisture being present in the fluid, it is still a good idea to change the fluid when it is suppose to be changed. ((Baphomet of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590)) Copper content is the most destructive aspect of brake fluid breakdown. \\ So even without moisture being present in the fluid, it is still a good idea to change the fluid when it is suppose to be changed. ((Baphomet of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590))
  
Line 40: Line 19:
 |1986-1990((1986-1990 HD Sportster FSM))|Check at initial 500 then every 5,000 miles, prior to storage or annually|Change/​ Replace as needed| |1986-1990((1986-1990 HD Sportster FSM))|Check at initial 500 then every 5,000 miles, prior to storage or annually|Change/​ Replace as needed|
 |1991 to 2003((1986-2003 Clymer Sportster Repair Manual))|Every 300 til and including initial 1,000 miles, then every 5,000 miles|Replace as needed| |1991 to 2003((1986-2003 Clymer Sportster Repair Manual))|Every 300 til and including initial 1,000 miles, then every 5,000 miles|Replace as needed|
- 
- 
----- 
    
-==== Testing Your Brake Fluid ====+===== Testing Your Brake Fluid =====
   * **Check water solubility** ​   * **Check water solubility** ​
   * What Type Brake Fluid Do You Have?    * What Type Brake Fluid Do You Have? 
Line 57: Line 33:
     * DOT 5.1 is available Clear, Pale Yellow & Blue.     * DOT 5.1 is available Clear, Pale Yellow & Blue.
     * DOT 5 is available in Purple & Violet. ((http://​advancepetro.com/​differentbrakefluid.htm))     * DOT 5 is available in Purple & Violet. ((http://​advancepetro.com/​differentbrakefluid.htm))
-      * Turns clear when it gets old. ((sportysrock of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​threadid=70213))+      * Turns clear during use (even though ​it is still fine to use). ((sportysrock of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​threadid=70213))
   * **Test for moisture content**: \\ This test is a result of an SAE paper showing a distinct relationship between moisture content and the voltage measured. ((turkishxl883 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590))   * **Test for moisture content**: \\ This test is a result of an SAE paper showing a distinct relationship between moisture content and the voltage measured. ((turkishxl883 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590))
   * Brake fluid (3,4 & 5.1) is hygroscopic (able to draw in moisture like a sponge). \\ It is no wonder, then, that the brake fluid in the master cylinder is often dark, almost black in appearance. \\ But does that mean it has to be changed? Not always. \\ Glycol based fluid absorbs moisture and disperses it throughout the system. \\ Silicone based (5) fluid does not allow moisture to enter the system. So this test may not work for DOT 5 fluid. ((steelworker of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590)) \\ (since it's the moisture inside the fluid that makes the reaction) \\ And while there are test strips to test the moisture content, \\ Here is a method that works just as well. \\ Use your DMM (Digital Multimeter) to test the fluid. ​   * Brake fluid (3,4 & 5.1) is hygroscopic (able to draw in moisture like a sponge). \\ It is no wonder, then, that the brake fluid in the master cylinder is often dark, almost black in appearance. \\ But does that mean it has to be changed? Not always. \\ Glycol based fluid absorbs moisture and disperses it throughout the system. \\ Silicone based (5) fluid does not allow moisture to enter the system. So this test may not work for DOT 5 fluid. ((steelworker of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1227590)) \\ (since it's the moisture inside the fluid that makes the reaction) \\ And while there are test strips to test the moisture content, \\ Here is a method that works just as well. \\ Use your DMM (Digital Multimeter) to test the fluid. ​
Line 65: Line 41:
     * Any reading over 0.30 volts is too much, and the fluid should be flushed.     * Any reading over 0.30 volts is too much, and the fluid should be flushed.
  
-==== Mixing Brake Fluids ====+===== Mixing Brake Fluids ​=====
   * Mixing different colors of the same type typically won't hurt the system. \\ (as long as what you are adding to has not been compromised previously if your just topping off your existing fluid)   * Mixing different colors of the same type typically won't hurt the system. \\ (as long as what you are adding to has not been compromised previously if your just topping off your existing fluid)
   * You can typically mix DOT 3,4 and 5.1 fluids without damaging your braking system or compromising your existing braking performance. \\ But as nearly every brake fluid manufacturer will state: doing so is not recommended. \\ Mixing good new fluid and old bad fluid means you will retain the bad fluid'​s performance. \\ (and change the temperature ratings of your residual fluid) \\ You can't mix any others with Dot 5 fluids. \\ Mixing the others into Dot 5 would cause a meltdown of the rubber parts and / or a break down of the silicone \\ (and possibly clog up the brake lines causing brake failure) \\ Dot 5 into the others may release clogs into the brake lines also leading to brake failure.  ​   * You can typically mix DOT 3,4 and 5.1 fluids without damaging your braking system or compromising your existing braking performance. \\ But as nearly every brake fluid manufacturer will state: doing so is not recommended. \\ Mixing good new fluid and old bad fluid means you will retain the bad fluid'​s performance. \\ (and change the temperature ratings of your residual fluid) \\ You can't mix any others with Dot 5 fluids. \\ Mixing the others into Dot 5 would cause a meltdown of the rubber parts and / or a break down of the silicone \\ (and possibly clog up the brake lines causing brake failure) \\ Dot 5 into the others may release clogs into the brake lines also leading to brake failure.  ​
   * If silicone is introduced into an older brake system; \\ The silicone will latch onto the sludge generated by gradual component deterioration and create a gelatin like goop. \\ (which will attract more crud and eventually plug up metering orifices or cause pistons to stick) \\ If you have already changed to DOT 5, don't compound the problem and change back. \\ You will never get all of the silicone out of your system. Just change the fluid regularly. \\ For those who race using silicone fluid; \\ Crack the bleed screws before each racing session to insure that there is no water in the calipers. ((http://​importnut.net/​brakefluid.htm))   * If silicone is introduced into an older brake system; \\ The silicone will latch onto the sludge generated by gradual component deterioration and create a gelatin like goop. \\ (which will attract more crud and eventually plug up metering orifices or cause pistons to stick) \\ If you have already changed to DOT 5, don't compound the problem and change back. \\ You will never get all of the silicone out of your system. Just change the fluid regularly. \\ For those who race using silicone fluid; \\ Crack the bleed screws before each racing session to insure that there is no water in the calipers. ((http://​importnut.net/​brakefluid.htm))
  
-  + Note the gooey mess from mixing Dot 5 and Dot 3 fluids. ((photos by FearlessFrisbee of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1508535)) ((photo by brianbbs67 of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​s=b7cdc14394b5d341991efe72f18f9aad&​t=1932868&​page=2)) ​ ||| 
-==== DOT 3, DOT 4, DOT 5.1 ====   +|{{:​techtalk:​ref:​wheels:​dot_5_-_dot_3_mix_goop_1_by_fearlessfrisbee.jpg?​direct&​300|}}|{{:​techtalk:​ref:​wheels:​dot_5_-_dot_3_mix_goop_2_by_fearlessfrisbee.jpg?​direct&​300|}}|{{:​techtalk:​ref:​wheels:​1977_front_master_cylinder_piston_gummed_up_by_brianbbs67.jpg?​direct&​300|}}| 
 +===== Swapping Brake Fluid (Dot 3 to Dot 5) ===== 
 + 
 +The following is found in HD Technical Service Bulletin M-712 dated June 16,1977. \\ 
 + 
 +When changing from D.O.T. 3 to D.O.T. 5 fluid or when flushing the brake system, it is important that D.O.T. 3 fluid be removed completely. \\ 
 +Old fluid could be contaminated with water and if mixed with the new D.O.T.-5 fluid, it would detract from it's effectiveness. \\ The old fluid could also cause varnish deposits if the system is operated above the boiling point of D.O.T. 3. \\ Caution should be used when bleeding because any brake fluid on the pad will contaminate the pad material and reduce brake effectiveness. \\ The fluid absorbed by the pads cannot be removed satisfactorily with any solvent nor by operating the brakes. 
 + 
 +**Procedure**:​ \\ 
 +  - Disconnect the brake lines from the master cylinder and wheel calipers (wheel cylinders if drum brakes). \\ Catch old fluid in container and discard. 
 +  - Remove master cylinder and brake calipers from motorcycle. 
 +  - Disconnect brake hoses from the metal brake lines (if applicable). 
 +  - Flush the metal brake lines several times with silicone brake fluid (D.O.T. 5) fluid to remove all the old fluid. \\ Solvent flushing is not recommended. 
 +  - Replace the brake hoses with new ones. 
 +  - Disassemble the master cylinder and wheel calipers or cylinders. 
 +  - Drain and remove any residual D.O.T. 3 brake fluid with a dry, clean cloth that will not leave lint or grit on the master cylinder or caliper parts. 
 +  - Replace master cylinder and wheel caliper rubber seals, piston cups and 0-rings with new parts. 
 +  - Coat pistons, piston bores and rubber parts with silicone brake fluid and reassemble. 
 +  - Install master cylinder and calipers on motorcycle. 
 +  - Reassemble brake lines to master cylinder and calipers. 
 +  - Fill brake system with D.O.T.-5 silicone brake fluid and bleed air from system following procedure in Service Manual. \\ Fluid leakage from the rear master cylinder boot after bleeding is often caused by excessive piston travel due to air in the system. \\ The boot should be wiped clean of any brake fluid to avoid contaminating the cylinder with road dust. 
 + 
 +===== DOT 3, DOT 4, DOT 5.1 =====   
   * DOT 3 brake fluids are mixtures of glycols and glycol ethers. DOT 4 contains borate esters in addition to what is in DOT 3. These brake fluids are somewhat similar to automotive anti-freeze (ethylene glycol) and are not a petroleum fluid. Both DOT 3-4 and DOT 5 fluids are compatible with most brake system materials except in the case of some silicone rubber external components such as caliper piston boots ((http://​importnut.net/​brakefluid.htm)) ​   * DOT 3 brake fluids are mixtures of glycols and glycol ethers. DOT 4 contains borate esters in addition to what is in DOT 3. These brake fluids are somewhat similar to automotive anti-freeze (ethylene glycol) and are not a petroleum fluid. Both DOT 3-4 and DOT 5 fluids are compatible with most brake system materials except in the case of some silicone rubber external components such as caliper piston boots ((http://​importnut.net/​brakefluid.htm)) ​
   * The problem with DOT 3-4 fluids is water absorption. DOT 3-4 glycol based fluids, just like ethylene glycol antifreezes,​ are readily miscible with water. Long term brake system water content tends to reach a maximum of about 3%, which is readily handled by the corrosion inhibitors in the brake fluid formulation. Since the inhibitors are gradually depleted as they do their job, glycol brake fluid, just like anti-freeze,​ needs to be changed periodically. ((http://​importnut.net/​brakefluid.htm))   * The problem with DOT 3-4 fluids is water absorption. DOT 3-4 glycol based fluids, just like ethylene glycol antifreezes,​ are readily miscible with water. Long term brake system water content tends to reach a maximum of about 3%, which is readily handled by the corrosion inhibitors in the brake fluid formulation. Since the inhibitors are gradually depleted as they do their job, glycol brake fluid, just like anti-freeze,​ needs to be changed periodically. ((http://​importnut.net/​brakefluid.htm))
Line 77: Line 75:
   * DOT 5.1 is also glycol-based and it's major difference to Dot 3 and 4 is it's dry boiling point (minimum 518F). ​   * DOT 5.1 is also glycol-based and it's major difference to Dot 3 and 4 is it's dry boiling point (minimum 518F). ​
  
-==== DOT 5 ====    ​+===== DOT 5 =====    ​
   * The change to Dot 5 brake fluid was made with HD production motorcycles in September of 1976 ((HD Service Letter M-28)). It is of silicone chemistry and not being water miscible, it must rely on the silicone (with some corrosion inhibitors) as a barrier film to control corrosion. Water is not absorbed by silicone as in the case of DOT 3-4-5.1 fluids, and will remain as a separate globule sinking to the lowest point in the brake system, since it is more dense. ((http://​importnut.net/​brakefluid.htm))   * The change to Dot 5 brake fluid was made with HD production motorcycles in September of 1976 ((HD Service Letter M-28)). It is of silicone chemistry and not being water miscible, it must rely on the silicone (with some corrosion inhibitors) as a barrier film to control corrosion. Water is not absorbed by silicone as in the case of DOT 3-4-5.1 fluids, and will remain as a separate globule sinking to the lowest point in the brake system, since it is more dense. ((http://​importnut.net/​brakefluid.htm))
   * When using Dot 3 brake fluid, the brake system should be drained, flushed, and refilled with new brake fluid every year to eliminate any contamination such as sludge. This yearly service was eliminated when D.O.T.-5 silicone fluid was used instead and with improved performance. ((HD Service Bulletin #M712 dated June 16, 1977 pg 1))   * When using Dot 3 brake fluid, the brake system should be drained, flushed, and refilled with new brake fluid every year to eliminate any contamination such as sludge. This yearly service was eliminated when D.O.T.-5 silicone fluid was used instead and with improved performance. ((HD Service Bulletin #M712 dated June 16, 1977 pg 1))
Line 83: Line 81:
   *  Dot 5 in its pure state offers a higher boiling point (500F) however if water got into the system, and a big globule found its way into a caliper, the water would start to boil at 212F causing a vapor lock condition (possible brake failure). DOT 3 fluid with 3% water content would still exhibit a boiling point of 300F. Silicone fluids also exhibit a 3 times greater propensity to dissolve air and other gasses which can lead to a "​spongy pedal" and reduced braking at high altitudes. ((http://​importnut.net/​brakefluid.htm))   *  Dot 5 in its pure state offers a higher boiling point (500F) however if water got into the system, and a big globule found its way into a caliper, the water would start to boil at 212F causing a vapor lock condition (possible brake failure). DOT 3 fluid with 3% water content would still exhibit a boiling point of 300F. Silicone fluids also exhibit a 3 times greater propensity to dissolve air and other gasses which can lead to a "​spongy pedal" and reduced braking at high altitudes. ((http://​importnut.net/​brakefluid.htm))
  
-==== Brake Fluid Boiling Points ====+===== Brake Fluid Boiling Points ​=====
   *Dry Boiling Point: This is the temperature that your brake fluid will boil when its straight out of the sealed bottle. When there has been effectively no time for it to absorb any moisture. If you are racing on a track, you are most concerned with this value, since the fluid in your lines is likely to be freshly added. ((https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm))   *Dry Boiling Point: This is the temperature that your brake fluid will boil when its straight out of the sealed bottle. When there has been effectively no time for it to absorb any moisture. If you are racing on a track, you are most concerned with this value, since the fluid in your lines is likely to be freshly added. ((https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm))
   *Wet Boiling Point: This is the temperature that your brake fluid will boil when its been inside your braking system for a reasonably long time. How long it takes to get to this saturation point will vary by fluid type, but a good rule of thumb is the higher the dry boiling point, the faster the fluid will saturate (an informal sort of standard is...not always - used by fluid manufacturers:​ the wet boiling point is the reading taken after fluid has been sitting for one year in your brake lines). If you are riding mainly on the street the wet boiling point is going to be the one you want to pay attention to since the fluid will typically stay in your brake lines for an extended period of time. ((https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm))   *Wet Boiling Point: This is the temperature that your brake fluid will boil when its been inside your braking system for a reasonably long time. How long it takes to get to this saturation point will vary by fluid type, but a good rule of thumb is the higher the dry boiling point, the faster the fluid will saturate (an informal sort of standard is...not always - used by fluid manufacturers:​ the wet boiling point is the reading taken after fluid has been sitting for one year in your brake lines). If you are riding mainly on the street the wet boiling point is going to be the one you want to pay attention to since the fluid will typically stay in your brake lines for an extended period of time. ((https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm))
  
-==== SAE Testing Brake Fluid Lubricity ====+===== SAE Testing Brake Fluid Lubricity ​=====
   * SAE is currently working on modernizing testing and standards for automotive brake fluids. Below are the standards that relate to brake fluid and their corresponding standard number. ​   * SAE is currently working on modernizing testing and standards for automotive brake fluids. Below are the standards that relate to brake fluid and their corresponding standard number. ​
     * J1703- Motor Vehicle Brake Fluid Jul 20, 2015      * J1703- Motor Vehicle Brake Fluid Jul 20, 2015 
Line 94: Line 92:
     * J1707- Service Maintenance of SAE J1703 and J1704 Brake Fluids in Motor Vehicle Brake Systems ​     * J1707- Service Maintenance of SAE J1703 and J1704 Brake Fluids in Motor Vehicle Brake Systems ​
  
-==== Links to Brake Fluid Comparison Charts on the Web ====+===== Links to Brake Fluid Comparison Charts on the Web =====
   * ((article by Matt Robertson))[[https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm]]   * ((article by Matt Robertson))[[https://​www.lelandwest.com/​brake-fluid-comparison-chart.cfm]]
   * ((Seine Systems))[[http://​www.seinesystems.com/​BrakeFluids.htm]]   * ((Seine Systems))[[http://​www.seinesystems.com/​BrakeFluids.htm]]