• Brake caliper mounting bolt O-rings- Dow Corning 44 grease (“Pin Lube” in parts kit) ¹⁾
• O.D. of brake caliper piston (including chamfer), caliper piston bore and I.D. of the installed piston seal - Novaguard silicon grease.
• I.D. of upper caliper (threaded) bushing bore, O.D. of threaded bushing, I.D. of upper and lower caliper mounting pin bores - Dow Corning 44 grease (“Pin Lube” in parts kit) ²⁾

Aftermarket brakes vs OEM brakes Check fitment of aftermarket brakes before using them. Just because they are published as 'will fit your vehicle' doesn't make it so. The pics below are a comparison of OEM brakes and an aftermarket brand:

These 2 different brand of brakes look very similar. 3)	The OEM pad on right has sharper contours 4)

The light colored OEM brake has sharper contours to match up to the screw mounting bracket shims it rides against. The aftermarket brand is slightly shorter in length than OEM which allows it to wiggle around a bit since it doesn't fit tight against the screw shims which can allow it to drop below the disc resulting in poor pad wear and possible disc wear or disc drag as in the pic below:

5)

Be sure your brakes can not wiggle around before installing the caliper.

Copper content is the most destructive aspect of brake fluid breakdown.
So even without moisture being present in the fluid, it is still a good idea to change the fluid when it is suppose to be changed. ¹⁰⁾

• Check water solubility
• What Type Brake Fluid Do You Have?
  • 1st check your bikes service manual to see what should go in it.
  • Next, get a few drops of brake fluid from your brake reservoir and put them in a small container. Add a few drops of water and mix it all together.
  • If the water mixes with the brake fluid, it is DOT 3, 4 or (5.1).
  • If the water does not mix with the brake fluid it is DOT 5. ¹⁵⁾
• The Color Check
• The presence or absence of color is not a safe criteria to distinguish between the different types of brake fluids.
  The color is added in brake fluid to detect leaks and color does not effect the quality of brake fluid.
  Since blue and purple sometimes can seem the same color depending on lighting, you could be mixing Dot 5 and DOT (5.1).
  (not to mention DOT 5 turning clear and making you think someone changed to a different type than OEM for your year model…. this does happen.)
  • DOT 3 is available in Clear, Pale Yellow, Blue & Crimson Red.
  • DOT 4 is available in Clear, Pale Yellow & Crimson Red.
  • DOT 5.1 is available Clear, Pale Yellow & Blue.
  • DOT 5 is available in Purple & Violet. ¹⁶⁾
    • Turns clear when it gets old. ¹⁷⁾
• Test for moisture content:
  This test is a result of an SAE paper showing a distinct relationship between moisture content and the voltage measured. ¹⁸⁾
• Brake fluid (3,4 & 5.1) is hygroscopic (able to draw in moisture like a sponge).
  It is no wonder, then, that the brake fluid in the master cylinder is often dark, almost black in appearance.
  But does that mean it has to be changed? Not always.
  Glycol based fluid absorbs moisture and disperses it throughout the system.
  Silicone based (5) fluid does not allow moisture to enter the system. So this test may not work for DOT 5 fluid. ¹⁹⁾
  (since it's the moisture inside the fluid that makes the reaction)
  And while there are test strips to test the moisture content,
  Here is a method that works just as well.
  Use your DMM (Digital Multimeter) to test the fluid.
• The procedure is easy enough.
  • Hook up your negative meter lead to the negative battery post.
  • Insert your positive meter lead into the brake fluid while avoiding contact with the reservoir itself.
  • Any reading over 0.30 volts is too much, and the fluid should be flushed.

• Mixing different colors of the same type typically won't hurt the system.
  (as long as what you are adding to has not been compromised previously if your just topping off your existing fluid)
• You can typically mix DOT 3,4 and 5.1 fluids without damaging your braking system or compromising your existing braking performance.
  But as nearly every brake fluid manufacturer will state: doing so is not recommended.
  Mixing good new fluid and old bad fluid means you will retain the bad fluid's performance.
  (and change the temperature ratings of your residual fluid)
  You can't mix any others with Dot 5 fluids.
  Mixing the others into Dot 5 would cause a meltdown of the rubber parts and / or a break down of the silicone
  (and possibly clog up the brake lines causing brake failure)
  Dot 5 into the others may release clogs into the brake lines also leading to brake failure.
• If silicone is introduced into an older brake system;
  The silicone will latch onto the sludge generated by gradual component deterioration and create a gelatin like goop.
  (which will attract more crud and eventually plug up metering orifices or cause pistons to stick)
  If you have already changed to DOT 5, don't compound the problem and change back.
  You will never get all of the silicone out of your system. Just change the fluid regularly.
  For those who race using silicone fluid;
  Crack the bleed screws before each racing session to insure that there is no water in the calipers. ²⁰⁾

• DOT 3 brake fluids are mixtures of glycols and glycol ethers. DOT 4 contains borate esters in addition to what is in DOT 3. These brake fluids are somewhat similar to automotive anti-freeze (ethylene glycol) and are not a petroleum fluid. Both DOT 3-4 and DOT 5 fluids are compatible with most brake system materials except in the case of some silicone rubber external components such as caliper piston boots ²¹⁾
• The problem with DOT 3-4 fluids is water absorption. DOT 3-4 glycol based fluids, just like ethylene glycol antifreezes, are readily miscible with water. Long term brake system water content tends to reach a maximum of about 3%, which is readily handled by the corrosion inhibitors in the brake fluid formulation. Since the inhibitors are gradually depleted as they do their job, glycol brake fluid, just like anti-freeze, needs to be changed periodically. ²²⁾
• Fluid boiling point DOT 4 glycol based fluid has a higher boiling point (446F) than DOT 3 (401F), and both fluids will exhibit a reduced boiling point as water content increases.²³⁾
• DOT 5.1 is also glycol-based and it's major difference to Dot 3 and 4 is it's dry boiling point (minimum 518F).

• The change to Dot 5 brake fluid was made with HD production motorcycles in September of 1976 ²⁴⁾. It is of silicone chemistry and not being water miscible, it must rely on the silicone (with some corrosion inhibitors) as a barrier film to control corrosion. Water is not absorbed by silicone as in the case of DOT 3-4-5.1 fluids, and will remain as a separate globule sinking to the lowest point in the brake system, since it is more dense. ²⁵⁾
• When using Dot 3 brake fluid, the brake system should be drained, flushed, and refilled with new brake fluid every year to eliminate any contamination such as sludge. This yearly service was eliminated when D.O.T.-5 silicone fluid was used instead and with improved performance. ²⁶⁾
• Silicone brake fluid reduces corrosion, will not degrade the “rubber” components, and sludge will not form in the system. It will not absorb water, does not attack painted parts, and has a higher boiling point than conventional brake fluid. When stored under normal conditions it has unlimited shelf life. However, it is somewhat harder to bleed brakes with Dot 5 because of its viscosity. ²⁷⁾
• Dot 5 in its pure state offers a higher boiling point (500F) however if water got into the system, and a big globule found its way into a caliper, the water would start to boil at 212F causing a vapor lock condition (possible brake failure). DOT 3 fluid with 3% water content would still exhibit a boiling point of 300F. Silicone fluids also exhibit a 3 times greater propensity to dissolve air and other gasses which can lead to a “spongy pedal” and reduced braking at high altitudes. ²⁸⁾

• Dry Boiling Point: This is the temperature that your brake fluid will boil when its straight out of the sealed bottle. When there has been effectively no time for it to absorb any moisture. If you are racing on a track, you are most concerned with this value, since the fluid in your lines is likely to be freshly added. ²⁹⁾
• Wet Boiling Point: This is the temperature that your brake fluid will boil when its been inside your braking system for a reasonably long time. How long it takes to get to this saturation point will vary by fluid type, but a good rule of thumb is the higher the dry boiling point, the faster the fluid will saturate (an informal sort of standard is…not always - used by fluid manufacturers: the wet boiling point is the reading taken after fluid has been sitting for one year in your brake lines). If you are riding mainly on the street the wet boiling point is going to be the one you want to pay attention to since the fluid will typically stay in your brake lines for an extended period of time. ³⁰⁾

• SAE is currently working on modernizing testing and standards for automotive brake fluids. Below are the standards that relate to brake fluid and their corresponding standard number.
  • J1703- Motor Vehicle Brake Fluid Jul 20, 2015
  • J1704- Motor Vehicle Brake Fluid Based Upon Glycols, Glycol Ethers and the Corresponding Borates Jul 20, 2015
  • J1705- Low Water Tolerant Brake Fluids Apr 21, 2014
  • J1707- Service Maintenance of SAE J1703 and J1704 Brake Fluids in Motor Vehicle Brake Systems

• ³¹⁾https://www.lelandwest.com/brake-fluid-comparison-chart.cfm
• ³²⁾http://www.seinesystems.com/BrakeFluids.htm
• ³³⁾http://worth-it.blogspot.com/2006/01/ultimate-brake-fluid-comparison-chart.html
• Interesting amateur test on mixing brake fluids http://www.buckeyetriumphs.org/technical/Brakes/Fluid/Fluid.htm