[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] ====== EVO: Carburetor, Intake Manifold & Exhaust ====== ====== Overview - Basic Stock Carb Model Info ====== From 1986-1987, the stock Sportster carburetor was a Keihin 34mm, fixed-venturi "butterfly" model, as used on the Ironhead models from 1979 onward (BT models still used the 38mm version). Contrary to popular folklore, all Keihin non-CV carbs did come with accelerator pumps. In 1988, the stock Sportster carburetor was upgraded to a Keihin 40mm, slide-type, constant-velocity model. It was quickly discovered that the lack of an accelerator pump was a shortcoming. To help that situation, a special needle, identified as 27094-88 or N65C, was used to help off-idle performance in the 1988 models, which still had no accelerator pump. In 1989 and thru 2006, the Keihin CV40 carburetors were produced with an accelerator pump to smooth out initial throttle response. \\ ====== Keihin Butterfly (non-CV) Carburetor (Stock on L1976-1987 Sportsters) ====== See also in the Sportsterpedia: \\ * [[techtalk:ih:carb01#keihin_butterfly_or_non-cv_carb_late_1976-1987|Keihin Butterfly Carb Basic Information]] * [[techtalk:ih:carb01q|Rebuilding the Keihin Butterfly Carb]] * [[techtalk:ih:carb01p|Keihin Butterfly Carb Identificaton]] * [[techtalk:miscres:miscres05#tsb_650-699|See TSB #694 for introduction information on the Keihin butterfly carb]]. \\ Click the link to view the TSB page in the Sportsterpedia. Then click on the "Y" next to #694 to view / download the PDF. \\ * The Keihin non-CV carburetor is a horizontal type with a fuel bowl, single ring-shaped float, an accelerating pump, idle mixture adjusting needle and a throttle stop screw for speed adjustment. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * The throttle body casting contains an integral venturi and a fuel valve seat that is pressed into the body. The underside of the throttle body contains a boss. The main jet screws into the boss and holds the bleed tube in place.((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * **Operation**: Fuel from the gas tank passes through the fuel valve, onto float chamber. The fuel entering causes the float to rise until it shuts off the fuel valve, stopping the flow at a level predetermined by float level setting. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * **Idle or Slow System**: The slow system functions at idle, low and intermediate speeds when throttle valve is closed or only partially open. At idle, fuel enters the main jet and, after being metered there, enters the slow jet where it is metered again. Fuel from the slow jet enters the slow jet bleed tube where it mixes with air through the slow air passage. Fuel mixture is regulated by adjusting the idle (low speed) mixture screw. When the throttle valve is closed, fuel mixture flows into the venturi almost entirely through the idle port. As the throttle valve gradually opens, fuel mix discharge is transferred to the bypass. The slow jet bleed tube is actually a part of the slow jet. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * **The Main System**: The main system functions at intermediate and high speeds as the throttle valve opens further. Fuel is metered by the main jet and enters the main jet air passage. The fuel/ air mixture then exits from the main nozzle and into the venturi. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * **The Accelerating Pump System**: The accelerating pump system works with sudden throttle openings (rapid acceleration) to quickly inject fuel into the carb to provide extra fuel for the engine demand. Rapid throttle action pushes the pump rod down, flexing the diaphragm, which compresses fuel underneath the diaphragm, forcing it up past the check valve and out the pump nozzle into the venturi. The check valve prevents backflow while the pump nozzle meters the flow. Spring action then returns the diaphragm back to it's original position. As the diaphragm returns, a new supply of fuel flows in and under it so the system will be ready to repeat the cycle with the next rapid throttle action detected. ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * **The Choke System**: The choke is manually set by pulling out on the choke button. Pulled all the way out is fully closed (for cold engine), partially open (for warm engine) or pushed all the way in, fully open (for warm engine). ((1970-1978 HD XL/XLH/XLCH/XLT 1000 FSM)) * Dual throttle cables * Integral Float Chamber * Manual Choke * 3 different models * 1976L-1978 have 38mm Venturi * 1979-1987 have 34mm Venturi * Model Year Changes **1986-1987 Features** ((1986-1990 HD Sportster FSM)) * 34mm Venturi * Horizontal, gravity fed with a float operated inlet valve * Throttle stop screw * Fast idle cam * Choke system with fast idle adjustment * Accelerator pump * Designed to control exhaust emissions * Fixed jets * Factory preset idle mixture * VOES port * Evaporative port \\ **Note**: \\ For those sold for use in California (as part of the evaporative emissions kit) the fuel overflow fitting was capped and the overflow line was removed. ((HD Service Bulletin #M-905 dated August 26, 1985)) ===== Factory Keihin Butterfly (non-CV) 34mm Carb by Sportster Model/Year ===== Note: Carb B83H was also used on 1983 Sportster models. \\ See a full list of all known Harley Keihin butterfly carbs here [[techtalk:ih:carb01#sportster_keihin_butterfly_carburetors_by_year_model|Sportster Keihin Butterfly Carburetors by Year Model]] in the ironhead section of the Sportsterpedia. ^Sportster Model^Year \\ Carb Used^HD Part Number^Flange \\ Number^ Main Jet \\ Size ^Low Speed \\ Jet Size^Initial Mixture \\ screw setting^Accel Pump \\ spring position^ |XL 883 (50 state)|1986-1987|27501-86A ((1986-1987 HD Sportster Parts Catalog pg 21))|B83H|155|52| |XL 1100 (50 state)|1986|27502-86A ((1986-1987 HD Sportster Parts Catalog pg 21))|B83H|155|52| |XL 1100 (50 state)|1987|27502-86B ((1986-1987 HD Sportster Parts Catalog pg 21))|B83H|150|52| * Main & Slow jet sizes are the same (86-87) 883 & (86) 1100. BUT - Due to internal differences, the carbs are not interchangeable ((1986-1990 HD XLH FSM pg 4-1)) \\ * Main Jet * 27087-80 - 1.50mm * 27098-78 - 1.55mm (std) * Slow Jet * 27329-83 - .52mm |Carb Idle Speed| 900 RPM ((Clymer Sportster Repair Manual 1959-1985))|| |Torque Specs ((1970-2010 Haynes Sportster Service and Repair Manual pgs 3.1-3.2)) ||| |1986-1987 |Carb to Intake Manifold Bolts |15-17 in/lbs (20-23 NM)| | * |Intake Manifold Flange to Cylinder Head Bolts/Nuts |72-120 in/lbs (8-14 Nm)| | * |Air Cleaner Backplate to Engine Bolts |120-144 in/lbs (14-16 Nm)| | * |Air Cleaner to Carburetor Bolts |36-60 in/lbs (4-7 Nm) | | * |Air Cleaner Cover Screws |36-60 in/lbs (4-7 Nm) | Interesting discussion here: https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/172520-stock-carb-size-on-1100-sportster?t=1847273 \\ \\ ====== Keihin BD / Screaming Eagle Carb ====== //Harley-Davidson motorcycles equipped with some Screamin’ Eagle® high-performance engine parts may not be used on public roads. \\ (and in some cases must be restricted to closed course competition) \\ This engine related performance part is intended for racing applications and is not legal for sale or use in California on pollution controlled motor vehicles. \\ // * Used in the Screaming Eagle Package line from HD as an Evolution XLH HI-FLO Carburetor & Air Cleaner. The carb was a (27001-88) * The kit Number is 29081-90C for 86 and later Sportsters. Carb stamping is (27FA) plus a 4 character date code. * Adjustable Accelerator Pump stroke * Incorporated a special intake manifold to carb spacer that had to be drilled and tapped (1/4 x 28) in the side for included Voes connection adapter * Required a 1987 replacement style intake manifold for 1988 and up models * Required possible grinding of the right rear corner of the front cylinder head, due to interference with the carburetor throttle pulley and cable guides, for proper clearance ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/43694-keihin-carb-diagram-and-settings?t=132922)) * Build kits and the bowl gasket are obsolete and hard to find. * The bowl gasket (27013-85) has been found at JW Boon.com but not the build kit. \\ [[https://jwboon.com/index2.php?content=https%3A//jwboon.com/dbhtml/catalog/Bool_OR/Fits_FLT%2520%2522Tour%2520Glide%2522/Section_inlet|Click here for a Link to their add]]. However, they do not ship to the U.S. * Dennis Kirk sells a kit that looks to have the correct bowl O-ring included under Parts Unlimited branding. Kit (1003-1671). \\ [[https://www.denniskirk.com/parts-unlimited/carb-rebuild-kit-1003-1671.p175288.prd/175288.sku|Click here for the link]]. However, according to the Q&A at the bottom of the page, the O-ring doesn't fit the SE carb. That needs to be verified. * Parts Unlimited shows kit# 175288 (1003-1671) as a replacement for the stock paper gasket on Yamahas, still a Keihin though and the gasket (O-ring) looks the same. \\ [[https://www.parts-unlimited.com/prod...umber=10031671|Click for the link]] * Speed Supplies.com has a listing for the bowl O-ring (27013-85) although there is no pic of it. ((LenC of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/199949-can-t-find-a-bowl-gasket-anywhere-options/page3?t=2076892&page=3)) \\ [[http://www.speedsupplies.com/partslisting.asp?position=312&increment=500&category=HD|Click here for the link]] ^ JET PART NUMBERS & SIZES (IN MM) FOR KEIHIN BD CARBURETORS ^^^^^^^^ ^Slow Jet ^Size | ^Int. Air/Fuel Jet ^Size | ^Main Jet ^Size | |27383-88 |42 | |27113-87 |Blank* | |27106-85 |1.30 | |27302-84 |50 | |27109-87 |55 | |27107-85 |1.35 | |27329-83 |52 | |27172-89 |60* | |27149-85 |1.40 | |27284-85 |55 | |27110-87 |80 | |27151-85 |1.45 | |27310-85 |58 | |27111-87 |1.00 | |27150-85 |1.50 | |27318-85 |60 | |27112-87 |1.20 | |27108-87 |1.60*| |27283-85 |62 | |27173-89 |1.70 | |27119-88 |1.65 | |27896-79 |65 | | || |27134-89 |1.70 | |27894-78 |68*| | || | || |27895-87 |70 | | || | || |27897-78 |72 | | || | || | * in carburetor |||||||| ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/43694-keihin-carb-diagram-and-settings?t=132922)) \\ ^ XLH Hi-Flo Carburetor and Air Cleaner Kit (29081-90C) Parts List |||||| |Item Description|Part No.|Item Description|Part No.|Item Description|Part No.| |VOES fitting|29190-85|Backplate|29075-91|Crankcase breather hose fitting|29034-85| |Gasket|27022-88|Button head screw|927A|O-ring|11110| |Manifold spacer|29275-88|Support spacer, \\ small I.D.|6786|Hose clamp|9946| |Carburetor assembly|27001-88|Support spacer, \\ large I.D.|6785|Venturi|29148-90| |Allen head bolts|3485A|Hex head bolt|3427|Air cleaner element|29025-88B| |Washer|6702|Allen head bolt|3587A|Vacuum hose kit|26553-94| |Lockwasher|7041|Washer|6333|Air cleaner trim|29024-88| |Air cleaner adapter|27041-90|Washer|6738|Bowl O-ring|27013-85| |Allen head bolt|885A|Gasket|27077-78|Rebuild Kit|91731-85A \\ See [[techtalk:miscres:miscres05#tsb_950-999|TSB M-961]]| |Nut|7686|Lockwasher|7068| |Washer|6228W|Air cleaner cover spacer|31523-88| |Carburetor gasket|27044-90|Counter-sunk allen head screw|3795| {{:techtalk:evo:carb:se_carb_functions.jpg?direct&300|}} {{:techtalk:evo:carb:se_high_flow_carb_1_by_88hugger.jpg?direct&300|}} ((photo by 88hugger of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/72194-carb-questions#post1906502)) {{:techtalk:evo:carb:se_high_flow_carb_2_by_88hugger.jpg?direct&300|}} ((photo by 88hugger of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/72194-carb-questions#post1906502)) \\ \\ ====== Keihin CV 40mm Carb (1988-2006) ====== \\ ===== Sub Documents ===== * [[techtalk:evo:carb01b|Keihin CV Carb Identification]] * [[techtalk:evo:carb01a|Rebuilding the Keihin CV Carb]] * [[:techtalk:evo:carb02|Keihin CV40 Carb Functions, Adjustments, Tuning]] ---- * Constant velocity, gravity fed - has a float-operated inlet valve and a vacuum-operated variable venturi (movable slide). * Both the CV40 and CVK carbs are made by Keihin in Japan. But only the CV is specific to a Harley and has the bar and shield and HD name on the side. ((CVPerformance of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/161092-accelerator-pump-diaphragm-wrong-size/page2?t=1729649&page=2)) \\ CVK is for Kawasaki and various other makes that contracted Keihin for that carburetor. \\ There is also a CV40 making the rounds that is distributed by a Florida company that looks identical but not all the specs match up. \\ There is no guarantee that any part (original or CVP) will fit those knock-off carburetors. \\ If your CV carb does not have the name Harley Davidson cast above the bowl on each side it is a knock-off. ^Torque Specs ^^^ |1988-2001 |Intake Manifold Flange to Cylinder Head Bolts/Nuts |72-120 in/lbs (8-14 Nm) | |2002-Later |Intake Manifold Flange to Cylinder Head Bolts/Nuts |96-144 in/lbs (10.9-16.3 Nm) | |All |Carb Clamp Screw |10-15 in/lbs (1.1-1.7 Nm)| == Operation: == * The carburetor atomizes gas in proper proportions to the air pulled in through the air intake. The throttle plate controls the amount of air flow. At idle, a small amount of gas is siphoned through the pilot jet by the incoming air and fed thru the Idle Port on the engine side of the throttle plate. As the throttle plate is opened farther, the air begins siphoning gas through the transfer ports (which are fed by the Pilot Jet) and eventually pulls gas thru the needle jet (which is fed by the main jet). The tapered needle, which moves up and down thru the fixed diameter needle jet, increases the flow of fuel as it is lifted up since it's taper gets smaller inside the needle jet, thus allowing for more flow when lifted up and out. The vacuum, in the air filter side of the throttle plate, is used to lift the slide barrel & needle jet. At full throttle, the carburetor venturi is fully opened and the needle is lifted far enough to allow the main jet to flow at full jet capacity. The choke circuit is actually an enrichment valve system to allow more fuel at startup. With the choke knob pulled out, a separate jet opening sends a stream of gas into the carburetor's venturi, on the engine side of the throttle plate, thus enriching the gas/air mixture when the engine is cold. The accelerator pump circuit injects a fine spray of gas into the carburetor intake during sudden twisting of the throttle to aid acceleration & reduce engine hesitation. ---- ===== Factory Keihin CV40 Carburetors by Sportster Model/Year ===== ===== Emissions Observations ===== by Almond farmer: ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/85814-best-carb-for-your-ironhead/page10?postid=5567479#post4106580)) * There were no HC emissions changes from 1981-2003 @ 2.5 g/km . * 78-79 is 14 g/km * 80-81 is 5 g/km * Any carburetor can meet those standards * In 2004 CARB went to 1.4 g/km and EPA (49 states)in 2006, last year for XL carburetor. * CA is the only state in the country with its own emissions standards which are currently the same as the EPA standards. * In 2008 CARB mandated only .8 k/km HC and EPA with the same requirement, followed two years later in 2010.
The above #s are combined HC + NOX
* Noticed the Keihin 40mms CV used 160 main jet for the 883 up to 2003, then 2004-2006 went to 175 (1.75mm) for 49 state bikes, not CA bikes. * This change makes the air/fuel mixture run richer, therefore, a richer mixture results in lower combustion temperature with resulting lower HC +NOX to meet more stringent emission standards. * Notice the 49 state 1200 used 170 jet up to 2004, 180 main jet (MJ) in 2004, & 185 MJ in 2005-2006. * CA 883 went from 170 MJ to 2003 then changed to 180 MJ in 2005-2006. * Again making the air/fuel ratio richer. * CA 1200 cc went from 160 MJ in 1989 to 185 MJ in 2006. So, the 2006, 1200 evo with Keihin 40mms CV with vertical needle used the same main jet (1.85mm)for all 50 states, since CARB & EPA had the same emission requirements on the MoCo in that time. * Note that jets are selected for operation at below 4000 ft elevation. * If installing CV to 1000cc IH would first select 170 main jet below 4000 ft elevation. This Keihin CV should return lower emissions than any of the Keihin Butterfly carburetors and even satisfied the tier 1 CARB emissions requirements. * Unfortunately, CV could satisfy tier 2 emissions at only .8 g/km. \\ ===== U S A (Domestic) Sportster Models ===== * All CV models come equipped with accelerator pump unless noted. * All data below is compiled from HD Parts Catalogs unless otherwise noted. * Sportster models are divided into 3 categories: Domestic, California & HDI models * See also: * [[techtalk:evo:carb01#u_s_a_california_sportster_models|California models]] * [[techtalk:evo:carb01#h_d_i_sportster_models|HDI models]] * See [[techtalk:evo:carb01#discrepancies_in_the_fsm_s_parts_catalog_s|Discrepancies in the FSM(s) / Parts Catalog(s)]] for further information on highlighted * areas in the carburetor charts below * See also [[techtalk:evo:carb01#Pics of Keihin CV Carbs That Were Factory Installed on Sportsters|Pics of Keihin CV Carbs That Were Factory Installed on Sportsters]] {{ :techtalk:evo:carb:cv40-needle-jet.jpg?180| Annotated by IXL2Relax at the XLForum}}{{ :techtalk:evo:carb:cv40-needle-em-jets.jpg?300| Photo by IXL2Relax at the XLForum}} Example Parts Shown Here >>>\\ \\ \\ **All CV40 carbs use the following parts & P/N:**\\ \\ 27100-88 - Needle Jet (.114" ID)((Don Burton at http://xlforum.net/forums/showthread.php?t=14949))\\ 27101-88 - Emulsion Tube (Needle Jet Holder)\\ 27585-88 - Vacuum Slide (Vacuum Piston)\\ \\ \\ ^Sportster Model^Year^ Keihin CV 40mm \\ Carb Serial # ^ Main / Slow \\ Jet Size ((Cross-reference numbers by Folkie from the XLFORUM http://xlforum.net/forums/showthread.php?t=2006132&page=7))^ Main / Slow Jet \\ (Part #s) ^ Keihin Needle \\ for Vac Slide((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) ^ |**XL883** (Dom)|1988|27501-88 \\ No Accel Pump|170 / 35|(27115-88) - (27117-88)|N65A (27091-88)| | |1989-1990|27501-89|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1991|27501-89A|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1992|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1993-1994|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1995|27489-92A|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1996|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95) \\ Listed for (Cal) only| | |1997|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |1998|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |1999-2001|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |2002-2003|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |2004-2006|27490-04|175 / 42|(27090-89) - (27171-89)|N9EY (28027-04)| |**XL883C** (Dom)|1998|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |1999-2001|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95) | |2002-2003|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |2004-2006|27490-04|175 / 42|(27090-89) - (27171-89)|N9EY (28027-04)| |**XL883 Hug** (Dom)|1988|27501-88 \\ No Accel Pump|170 / 35|(27115-88) - (27117-88)|N65A (27091-88)| | |1989-1990|27501-89|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1991|27501-89A|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1992|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1993-1994|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1995|27489-92A|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1996|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95) \\ Listed for (Cal) only| | |1997|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |1998|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |1999-2001|27490-96|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |2002-2003|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| |**XL883 Deluxe** (Dom)|1988|27501-88 \\ No Accel Pump|170 / 35|(27115-88) - (27117-88)|N65A (27091-88)| | |1989-1990|27501-89|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1991|27501-89A|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1992|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1993-1994|27489-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |1995|27489-92A|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| |**XL883L** (Dom)|2005-2006|27490-04|175 / 42|(27090-89) - (27171-89)|N9EY (28027-04)| |**XL883R** (Dom)|2002-2003|27490-96A|160 / 42|(27152-89) - (27271-89)|NOKK (27241-95)| | |2005-2006|27490-04|175 / 42|(27090-89) - (27171-89)|N9EY (28027-04)| |**XL1200** (Dom)|1988|27502-88|200 / 35|(27105-88) - (27117-88)|N65C (27094-88)| | |1989|27502-89|175 / 45|(27090-89) - (27170-89)|N72E (27168-89)| | |1990|27501-89|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1991|27501-89A|175 / 45|(27090-89) - (27170-89)|N72A (27166-89)| | |1992-1994|27487-92|170 / 40|(27115-88) - (27281-92)|N86P (27280-92)| | |1995|27487-92A|160 / 40|(27152-89) - (27281-92)|N86P (27280-92)| | |1996|27491-96|160 / 42|(27152-89) - (27171-89)|N86P (27280-92)| | |1997|27480-97|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1998|27480-97A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1999-2001|27480-97|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2002-2003|27480-97A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| |**XL1200C** (Dom)|1996|27491-96|160 / 42|(27152-89) - (27171-89)|N86P (27280-92)| | |1997|27480-97|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1998|27480-97A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1999-2001|27480-97|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2002-2003|27480-97A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2004|27731-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| | |2005-2006|27731-04|185 / 42|(27185-90) - (27171-89)|N4NN (28026-04)| |**XL1200R** (Dom)|2004|27731-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| | |2005-2006|27731-04|185 / 42|(27185-90) - (27171-89)|N4NN(28026-04)| |**XL1200S** (Dom)|1996|27491-96|160 / 42|(27152-89) - (27171-89)|N86P (27280-92)| | |1997|27480-97|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |**NOTE:** 1998-2003 1200S carbs have no float bowl overflow tube protection\\ They also have no drain plug & hose to empty float chamber for off riding season or extended storage||||| | |1998|27731-98A|195((1998 HD XLH FSM pg 4-1)) / 42|(27275-96Y) - (27171-89)|NOKK (27241-95)| | |1999-2001|27731-98|195 / 42|(27275-96Y) - (27171-89)|(27656-98)| | |2002-2003|27731-98A|195 / 42|(27275-96Y) - (27171-89)|(27656-98)| ===== U S A (California) Sportster Models ===== * All CV models come equipped with accelerator pump unless noted. * All data below is compiled from HD Parts Catalogs unless otherwise noted. * Sportster models are divided into 3 categories: Domestic, California & HDI models * See also: * [[techtalk:evo:carb01#u_s_a_domestic_sportster_models|Domestic models]] * [[techtalk:evo:carb01#h_d_i_sportster_models|HDI models]] * See [[techtalk:evo:carb01#discrepancies_in_the_fsm_s_parts_catalog_s|Discrepancies in the FSM(s) / Parts Catalog(s)]] for further information on highlighted * areas in the carburetor charts below * See also [[techtalk:evo:carb01#Pics of Keihin CV Carbs That Were Factory Installed on Sportsters|Pics of Keihin CV Carbs That Were Factory Installed on Sportsters]] {{ :techtalk:evo:carb:cv40-needle-jet.jpg?180| Annotated by IXL2Relax at the XLForum}}{{ :techtalk:evo:carb:cv40-needle-em-jets.jpg?300| Photo by IXL2Relax at the XLForum}} Example Parts Shown Here >>>\\ \\ \\ **All CV40 carbs use the following parts & P/N:**\\ \\ 27100-88 - Needle Jet (.114" ID)((Don Burton at http://xlforum.net/forums/showthread.php?t=14949))\\ 27101-88 - Emulsion Tube (Needle Jet Holder)\\ 27585-88 - Vacuum Slide (Vacuum Piston)\\ \\ \\ ^Sportster Model^Year^ Keihin CV 40mm \\ Carb Serial # ^ Main / Slow \\ Jet Size ((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7))^ Main / Slow Jet \\ (Part #s) ^ Keihin Needle \\ for Vac Slide((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) ^ |**XL883** (Cal)|1988|27504-88 \\ No Accel Pump|165 / 35|(27116-88) - (27117-88)|N65B (27092-88)| | |1989|27504-88A|? / 42 \\ 155 / 42 ((1886-1990 HD Sportster FSM pg 4-1))| (27154-88)((1986-1990 HD Sportster Parts Catalog pg 23)) - (27171-89) \\ (27154-89)((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) - (27171-89)|N72B (27167-89)| | |1990|27503-88A|? / 42 \\ 160 / 42 ((1886-1990 HD Sportster FSM pg 4-1))|(27152-88)((1986-1990 HD Sportster Parts Catalog pg 23)) - (27171-89) \\ (27152-89)((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) - (27171-89)|N72F (27169-89)| | |1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F (27169-89)| | |1992- Early 1993|27488-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |Late 1993-1994|27488-92A|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| | |1995|27488-92B|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| | |1996-1997|27495-96|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1998|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1999-2001|27495-96|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2002-2003|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2004|27495-04|185 / 42|(27185-90) - (27171-89)|N4NN (28026-04)| | |2005-2006|27495-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| |**XL883C** (Cal)|1998|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1999-2001|27495-96|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2002-2003|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2004|27495-04|185 / 42|(27185-90) - (27171-89)|N4NN (28026-04)| | |2005-2006|27495-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| |**XL883 Hug** (Cal)|1988|27504-88 \\ No Accel Pump|165 / 35|(27116-88) - (27117-88)|N65B (27092-88)| | |1989|27504-88A|? / 42 \\ 155 / 42 ((1886-1990 HD Sportster FSM pg 4-1))| (27154-88)((1986-1990 HD Sportster Parts Catalog pg 23)) - (27171-89) \\ (27154-89)((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) - (27171-89)|N72B (27167-89)| | |1990|27503-88A|? / 42 \\ 160 / 42 ((1886-1990 HD Sportster FSM pg 4-1))|(27152-88)((1986-1990 HD Sportster Parts Catalog pg 23)) - (27171-89) \\ (27152-89) - (27171-89)|N72F (27169-89)| | |1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F (27169-89)| | |1992- Early 1993|27488-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |Late 1993-1994|27488-92A|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| | |1995|27488-92B|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| | |1996-1997|27495-96|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1998|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |1999-2001|27495-96|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2002-2003|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK(27241-95)| |**XL883 Deluxe** (Cal)|1988|27504-88 \\ No Accel Pump|165 / 35|(27116-88) - (27117-88)|N65B (27092-88)| | |1989|27504-88A|165 / 42|(27116-88) - (27171-89)|N72B (27167-89)| | |1990|27503-88A|165 / 42|(27116-88) - (27171-89)|N72F (27169-89)| | |1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F (27169-89)| | |1992- Early 1993|27488-92|160 / 40|(27152-89) - (27281-92)|N86Q (27183-92)| | |Late 1993-1994|27488-92A|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| | |1995|27488-92B|170 / 40|(27115-88) - (27281-92)|N86K (27278-93)| |**XL883L** (Cal)|2005-2006|27495-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| |**XL883R** (Cal)|2002-2003|27495-96A|170 / 42|(27115-88) - (27171-89)|NOKK (27241-95)| | |2005-2006|27495-04|180 / 42|(27114-88) - (27171-89)|N4NN (28026-04)| |**XL1200** (Cal)|1988|27503-88 \\ No Accel Pump|180 / 35|( 27114-88) - (27117-88)|N65D (27099-88)| | |1989-1990|27503-88A|? / 42 \\ 160((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) / 42|( 27152-88 ) (('86-'90 parts catalog lists 27152-88. Corrected to 27152-89 by the '86-'90 FSM and ((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) \\ (27152-89) - (27171-89)|N72F (27169-89)| | |1991|27503-88B|160 / 42|( 27152-89) - (27171-89)|N72F (27169-89)| | |1992-Early 1993|27486-92|170((1991-1992 HD Sportster FSM pg 4-1)) / 40|(27115-88)- (27281-92)|N86P (27280-92)| | |Late 1993-1994|27486-92A|185 / 40|(27185-90) - (27281-92)|N86J (27279-93)| | |1995|27486-92B| 185 / 40|(27185-90) - (27281-92)|N86J (27279-93)| | |1996-1997|27498-96|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |1998|27498-96A| 185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |1999-2001|27498-96|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |2002-2003|27498-96A|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| |**XL1200C** (Cal)|1996-1997|27498-96| 185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |1998|27498-96A|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |1999-2001|27498-96|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |2002-2003|27498-96A|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |2004-2006|27732-04|185 / 42|(27185-90) - (27171-89)|N4NN (28026-04)| |**XL1200R** (Cal)|2004-2006|27732-04|185 / 42|(27185-90) - (27171-89)|N4NN (28026-04)| |**XL1200S** (Cal)|1996|27498-96|185 / 42|(27185-90) - (27171-89)|N86J (27279-93)| | |1997|27498-96|195 / 42|(27275-96Y) - (27171-89)|N86J (27279-93)| | |**NOTE:** 1998-2003 1200S carbs have no float bowl overflow tube protection\\ They also have no drain plug & hose to empty float chamber for off riding season or extended storage||||| | |1998|27732-98A|195 / 42|(27275-96Y) - (27171-89)|N86J (27279-93)| | |1999-2001|27732-98|195 / 42|(27275-96Y) - (27171-89)|(27254-96)| | |2002-2003|27732-98A|195 / 42|(27275-96Y) - (27171-89)|(27254-96)| ===== H D I Sportster Models ===== * All CV models come equipped with accelerator pump unless noted. * All data below is compiled from HD Parts Catalogs unless otherwise noted. * Sportster models are divided into 3 categories: Domestic, California & HDI models * See also: * [[techtalk:evo:carb01#u_s_a_domestic_sportster_models|Domestic models]] * [[techtalk:evo:carb01#u_s_a_california_sportster_models|California models]] * See [[techtalk:evo:carb01#discrepancies_in_the_fsm_s_parts_catalog_s|Discrepancies in the FSM(s) / Parts Catalog(s)]] for further information on highlighted * areas in the carburetor charts below * See also [[techtalk:evo:carb01#Pics of Keihin CV Carbs That Were Factory Installed on Sportsters|Pics of Keihin CV Carbs That Were Factory Installed on Sportsters]] {{ :techtalk:evo:carb:cv40-needle-jet.jpg?180| Annotated by IXL2Relax at the XLForum}}{{ :techtalk:evo:carb:cv40-needle-em-jets.jpg?300| Photo by IXL2Relax at the XLForum}} Example Parts Shown Here >>>\\ \\ \\ **All CV40 carbs use the following parts & P/N:**\\ \\ 27100-88 - Needle Jet (.114" ID)((Don Burton at https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/9621-carb-adjusting-where-are-the-jets-and-the-mixture-screw?t=14949))\\ 27101-88 - Emulsion Tube (Needle Jet Holder)\\ 27585-88 - Vacuum Slide (Vacuum Piston)\\ \\ \\ ^Sportster Model^Year^ Keihin CV 40mm \\ Carb Serial # ^ Main / Slow \\ Jet Size ((Cross-reference numbers by Folkie from the XLFORUM http://xlforum.net/forums/showthread.php?t=2006132&page=7))^ Main / Slow Jet \\ (Part #s) ^ Keihin Needle \\ for Vac Slide((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) ^ |**XL883** Swiss \\ All Models|1989-1990|27492-89 \\ No Accel Pump|? / 35|(27104-89) - (27117-88)|? (27164-89?)| |**XL883** \\ HDI / Swiss|1989-1990|27501-88 \\ No Accel Pump|? / 35|(27104-89) - (27117-88)|? (27164-89)| |**XL883** Swiss|1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1992|27503-92|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1993-1994|27503-92A|160 / 40|(27152-89) - (27281-92)|N65J(27187-93)| |HDI|1995-1997|27031-95|190 / 42|(27243-95) - (27171-89)|N65J (27187-93)((Not listed in 1997 Parts Catalog))| |HDI|1998|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI|1999-2000|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI/Eng/Japan |2001|27465-01|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |HDI \\ Eng/Japan|2002-2003|27465-01A|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |Aust|2001|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |Aust|2002-2003|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI|2004-2006|27465-04|165 / 42|(27116-88) - (27171-89)|N9EY (28027-04)| |**XL883C** HDI|1999-2000|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI/Eng/Japan |2001|27465-01|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |HDI/Eng/Japan |2002-2003|27465-01A|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |Aust|2001|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |Aust|2002-2003|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI|2004-2006|27465-04|165 / 42|(27116-88) - (27171-89)|N9EY(28027-04)| |**XL883 Hug** Swiss|1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1992|27503-92|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1993-1994|27503-92A|160 / 40|(27152-89) - (27281-92)|N65J(27187-93)| |HDI|1995-1997|27031-95|190 / 42|(27243-95) - (27171-89)|N65J (27187-93)((Not listed in 1997 Parts Catalog))| |HDI|1998|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI|1999-2000|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI/Eng/Japan |2001|27465-01|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |HDI/Eng/Japan |2002-2003|27465-01A|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |Aust|2001|27031-95|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |Aust|2002-2003|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |**XL883 Deluxe** Swiss|1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1992|27503-92|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1993-1994|27503-92A|160 / 40|(27152-89) - (27281-92)|N65J(27187-93)| |HDI|1995|27031-95|190 / 42|(27243-95) - (27171-89)|N65J (27187-93)| |**XL883L** \\ HDI|2005-2006|27465-04|165 / 42|(27116-88) - (27171-89)|N9EY(28027-04)| |**XL883R** \\ HDI/Eng/Japan |2002-2003|27465-01A|165 / 42|(27116-88) - (27171-89)|NOKL (28013-01)| |Aust |2002-2003|27031-95A|190 / 42|(27243-95) - (27171-89)|NOKD (27242-95)| |HDI |2005-2006|27465-04|165 / 42|(27116-88) - (27171-89)|N9EY (28027-04)| |**XL1200** \\ HDI / Swiss|1988-1990 \\ No Accel Pump|27502-88|? / ?|(?) - (?)|? - (?)| |Swiss|1989-1990 \\ No Accel Pump|27491-89|? / 35|(27104-89) - (27117-88)|? (27165-89)| |Swiss|1991|27503-88B|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1992|27503-92|160 / 42|(27152-89) - (27171-89)|N72F(27169-89)| |HDI / Swiss|1993-1994|27503-92A|160 / 40|(27152-89) - (27281-92)|N65J(27187-93)| |HDI|1995|27076-95|190 / 42|(27243-95) - (27171-89)|N65J(27187-93)| |Swiss ((all models: 95-96 Parts Catalog doesn't say which models were shipped Swiss))|1995|27503-92B|160 / 40|(27152-89) - (27281-92)|N65J(27187-93)| |HDI|1998|27076-95A|190 / 42|(27243-95) - (27171-89)|NOKK (27241-95)| |HDI|1999-2000|27076-95|190 / 42|(27243-95) - (27171-89)|NOKK (27241-95)| |HDI/Aust/Eng/Japan|2001|27076-95|190 / 42|(27243-95) - (27171-89)|NOKK (27241-95)| |HDI/Aust/Eng/Japan|2002-2003|27076-95A|190 / 42|(27243-95) - (27171-89)|NOKK (27241-95)| |**XL1200C** \\ HDI|1996-1997|27076-95|190 / 42|(27243-95) - (27171-89)|N65J(27187-93)((Not listed in 2007 Parts Catalog))| |HDI|1998|27076-95A|190 / 42|(27243-95) - (27171-89)|NOKK (27241-95)| |HDI|1999-2000|27076-95|190 / 42|(27243-95) - (27171-89)|NOKK(27241-95)| |HDI/Aust/Eng/Japan|2001|27076-95|190 / 42|(27243-95) - (27171-89)|NOKK(27241-95)| |HDI/Aust/Eng/Japan|2002-2003|27076-95A|190 / 42|(27243-95) - (27171-89)|NOKK(27241-95)| |HDI |2004-2006|27749-04|160 / 42|(27152-89) - (27171-89) \\ HDI, Japan|N9EY (28027-04)| |**XL1200R** \\ HDI|2004-2006|27749-04|160 / 42|(27152-89) - (27171-89) \\ HDI, Japan|N9EY (28027-04)| |**XL1200S** \\ HDI|1996-1997|27076-95|190 / 42|(27243-95) - (27171-89)|N65J(27187-93)((Not listed in 2007 Parts Catalog))| |HDI|1998|27734-98|190 ((1998 HD XLH FSM pg 4-1)) / 42|(27243-95)((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) - (27171-89)|N86K (27278-93)| |Swiss|1998|27733-98|195 ((1998 HD XLH FSM pg 4-1)) / 42|(27275-96Y)((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7)) - (27171-89)|N86K (27278-93)| |HDI|1999-2000|27734-98|200 / 42|(27105-88) - (27171-89)|N86K (27278-93)| |HDI/Aust/Eng/Japan|2001|27749-01|185 / 42|(27185-90) - (27171-89)|(27647-01)| |HDI/Aust/Eng/Japan|2002-2003|27749-01A|185 / 42|(27185-90) - (27171-89)|(27647-01)| \\ ===== Slow & Main Jets - P/N & Comparisons ===== ^ Chart of Slow (Pilot) Jet Size Differences ||||||| | Number | HD Part # | MM | Dia Inches | Area Inch² | %+ of\\ Prev Jet | %± of\\ 42 Jet | ^ ||||||| | Keihin 35 | 27117-88 | 0.35 | 0.013780 | 0.0001491 | ~~ | -30.56 | | Keihin 40 | 27281-92 | 0.40 | 0.015748 | 0.0001947 | 30.61 | -9.30 | | Keihin 42 | 27171-89 | 0.42 | 0.016535 | 0.0002146 | 10.25 | --TYP-- | | Keihin 45 | 27170-89 | 0.45 | 0.017717 | 0.0002464 | 14.80 | 14.80 | | Keihin 48 | 27165-90 | 0.48 | 0.018898 | 0.0002803 | 13.78 | 30.61 | | ||||||| | Keihin 44 | CV-Perf | 0.44 | 0.017323 | 0.0002356 | | 9.75 | | Keihin 46 | CV-Perf | 0.46 | 0.018110 | 0.0002575 | | 19.95 | | Keihin 50 | CV-Perf | 0.50 | 0.019685 | 0.0003042 | | 41.72 | | ||||||| | CV-Perf is for CV-Performance.com ||||||| | Keihin P/N for above listed jets is N424-25B-XX <-- where XX is the size ||||||| | The N424-25B-XX series jets have 0.8mm bleed (cross) holes ||||||| | ||||||| ^ Chart of Main Jet Size Differences ||||||| | Number | HD Part # | MM | Dia Inches | Area Inch² | %+ of\\ Prev Jet | %± of\\ 170 Jet | ^ ||||||| | Keihin 160 | 27152-89 | 1.60 | 0.062992 | 0.0031149 | ~~ | -11.42 | | Keihin 165 | 27116-88 | 1.65 | 0.064961 | 0.0033126 | 6.35 | -5.80 | | Keihin 170 | 27115-88 | 1.70 | 0.066929 | 0.0035164 | 6.15 | --TYP-- | | Keihin 175 | 27090-89 | 1.75 | 0.068898 | 0.0037263 | 5.97 | 5.97 | | Keihin 180 | 27114-88 | 1.80 | 0.070866 | 0.0039423 | 5.80 | 12.11 | | Keihin 185 | 27185-90 | 1.85 | 0.072835 | 0.0041643 | 5.63 | 18.43 | | Keihin 190 | 27243-95 | 1.90 | 0.074803 | 0.0043925 | 5.48 | 24.91 | | Keihin 195 | 27275-96Y | 1.95 | 0.076772 | 0.0046267 | 5.33 | 31.57 | | Keihin 200 | 27105-88 | 2.00 | 0.078740 | 0.0048670 | 5.19 | 38.41 | | ||||||| | Keihin P/N for above listed jets is N424-27-XXX <-- where XXX is the size ||||||| | Area Inch² = 3.14 * DiaInches/2 * DiaInches/2 = π*r² ||||||| \\ ====== Discrepancies in the FSM(s) / Parts Catalog(s) ====== Upon perusing 1986-2006 Parts Catalogs for carburetor information, it's clear that the MoCo was trying to save space in these books at the expense of legibility. Below is a chart showing the initial intentions on the top and the MoCo's mis-interpretations on the bottom. They give no notations (from year to year book) on any changes to the nomenclature. I.E. one way to display a year/ model number is displayed differently in other year books. This chart is not complete nor factual in numbering but as an example only. For instance: |Parts Book|Description|For Model(s)|Part fits model(s)|Notes| |86-90|00000-86|88 - * XL1200|(88-90) XL1200|Easy to understand, * means \\ to the last date the book covers| |86-90|00000-86 (86-87 883)|90-XL1200|(86-87) XL883 & (90) XL1200|Little harder \\ (more to think about)| |86-90|00000-86|86-* all models|(86-90) XL883 all & (88-90) XL1200|Easy to understand, blankets all models 1200 \\ first made in 1988 but it leads you to believe \\ they were made from '86| |86-90|00000-86\\ 00000-86 (Cal)|89-* XL1200 \\ 88-* XL1200|(89-90) XL1200 - (49 state)except California \\ (88-90) XL1200 - California only|No suffix after desc. means domestic models \\ (Cal) after suffix is California models only| |91-92|00000-86 \\ (91-Cal)|91-* XL1200|(91-92) Xl1200 (domestic) \\ (91) Xl1200 (California)|Both Cal and Dom models| |93-94|00000-87 (93-Cal)\\ 00000-86|93-* XL883\\ 93-* XL883|(93-94) Xl883 (California) only\\ (93-94) XL883 all models|Reads it but doesn't mean for Domestic\\ Domestic (49 state models)| **Found and documented discrepancies are in the chart below**. I'm sure I didn't list them all ((Hippysmack)) |Engine |XL883|||XL1200||| |**2004 FSM** (erroneous info)((Folkie https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7))|49 State|California|HDI, Swiss|49 State|California|HDI, Swiss| |Main Jet \\ Corrected Size ((Verified with the 2004 HD Sportster Parts Catalog pgs 21,23))|160 \\ 175|170 \\ 180|190 \\ 170|175/190 \\ 180|185-195 \\ 185|200 \\ 160| |**2002, 2003 Parts Catalogs** show a Cali 883R carb but no jet sizes or other carb parts. \\ Listed same year 883 (Cali) data.((hippysmack))||||||| |**1999, 2000 Parts Catalogs** do not list part number for a (Cali) main jet size for the 1200S. \\ Listed same year (Dom) jet sizes.((hippysmack))||||||| |**1999, 2000 Parts Catalog** does not list part number for a (Cali) main jet size for the 883C. \\ Listed same year (Cali) 883 jet sizes.((hippysmack))||||||| |1998 Parts Catalog shows a 170 and a 195 main jet for Dom 1200S. \\ Verified with 1998 HD Sportster FSM to be a 195.((hippysmack))||||||| |**1998 Parts Catalog** pg 135 lists differences between the mid-year intro 883C and 883Std. \\ Reads other than what's listed, use 883Std parts. No carb parts listed so Std 883 specs used.((hippysmack))||||||| |**1998 Parts Catalog** pg 23 shows Swiss 1200S with (27114-88) 180 main jet but no main jet for HDI. Also there is no jet needle specified for Swiss 1200S \\ Listed jet sizes from 1998 HD FSM pg 4-1 showing Swiss (195), HDI (190). Also listed Swiss 1200S jet needle as same year HDI 1200S ((hippysmack))||||||| |**1998 Parts Catalog** shows 1200S (Dom) main jet as a 170 (27115-88). \\ Corrected to a 195 main jet with the 1998 HD XLH FSM pg 4-1.((hippysmack))||||||| |**1993-1994 Parts Catalog** makes it impossible to verify a main jet without the FSM to translate;||||||| |27115-88 Main Jet (Late 1992 and Later 883 Cal.) 93-94 All Models|Translates to Cal 883 (170) & Dom 1200 (170)((hippysmack))|||||| |27152-89 Main Jet (1200 HDI and Swiss) 93-94 All Models|Translates to Dom, HDI/Swiss 883 (160) & HDI/Swiss 1200 (160)((hippysmack))|||||| |27185-90 Main Jet (Cal only) L93-94 1200|Normal listing which is a Late 93-94 Cal 1200 (185)((hippysmack))|||||| |**1991-1992 Parts Catalog** is confusing to show (Cal)1200 main jet as: (170) 27115-88 - main Jet (Dom) - 92 and on * -all models.((hippysmack))||||||| |**1991-1992 Parts Catalog** is confusing to show (Cal)883 main jet as: (160) 27152-89 - main Jet (1991 Cal & Swiss; 1992 & later All 883, 1200 HDI & Swiss - 1991-1992 models. Doesn't seem to group (Cal)883 into the 92 models. Verified with 1991-1992 FSM pg 4-1((hippysmack))||||||| |**1990 Parts Catalog** does not list a main jet for an XL1200 (Domestic) model. \\ Verified with the 1986-1990 FSM pg 4-1.((hippysmack))||||||| |**1986-1990 Parts Catalog** has an errant main jet #27154-88 for (Cal) 883s. Confirmed as a 155 with the 1986-1990 Sportster FSM pg 4-1, cross referenced to serial #27154-89 ((Cross-reference numbers by Folkie from the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/188380-cv-carb-clogged-tiny-main-air-jet/page7?t=2006132&page=7))((hippysmack))||||||| |**1986-1990 Parts Catalog** is very confusing on export model carb info. I.E., \\ **The carb numbers are (all with no accel pump)**: \\ 27491-89 / (Swiss only) / 89-90 XLH1200 \\ 27492-89 / Swiss only / 89-90 XLH883 All Models \\ 27501-88 / HDI only-1989 & later / 88-90 XL883 All Models \\ 27502-88 / HDI only-1989 & later / 88-90 XLH1200 \\ **These are the only main jets designated for export motors:** \\ 27102-89 / Main Jet (Swiss only) / 89- XLH 883 All Models \\ 27104-89 / Main jet (Swiss only) / 89-90 All Models \\ **These are the only slow jets designated for export motors:** \\ 27117-88 / Slow jet (Swiss only-1989) / 88 & 89 All Models \\ **These are the only needle jets designated for export motors:** \\ 27164-89 (Swiss only) / 89- XLH 883 All models \\ 27165-89 (Swiss only) / 89- XL1200 \\ **Everything else is either designated Domestic or California engines.** ((hippysmack))||||||| \\ [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]