Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:evo:engmech01g [2022/04/01 22:47] hippysmack [Machining Date (2004-up)] |
techtalk:evo:engmech01g [2022/04/02 07:18] hippysmack [2004-Up Cam Covers] |
||
---|---|---|---|
Line 53: | Line 53: | ||
|{{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_25219-86_by_deadpartsmc_pic5.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_date_codes.jpg?direct&300|}}| | |{{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_25219-86_by_deadpartsmc_pic5.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_date_codes.jpg?direct&300|}}| | ||
- | ===== Machining Date (2004-up) ===== | + | ===== Machining Dates (2004-up) ===== |
2004-up cam covers have a several numbers pin stamped on the inside of the cover. \\ | 2004-up cam covers have a several numbers pin stamped on the inside of the cover. \\ | ||
Original location was on the rear near the oil tank breather fitting. \\ | Original location was on the rear near the oil tank breather fitting. \\ | ||
Later covers were stamped on the inside front in the round portion behind the oil filter mount. \\ | Later covers were stamped on the inside front in the round portion behind the oil filter mount. \\ | ||
- | There are 2 sets of numbers with the first being the month, day and year followed by a set of unknown numbers. \\ | + | There are 2 sets of numbers with the first being the month, day and year of machining (holes drilled, bushings installed/reamed etc.) \\ |
- | The unknown numbers may be production, control or operator numbers and possibly a mix of these. \\ | + | The next set of numbers are for unknown reasons at this time. \\ |
+ | The unknown numbers may be production, control or operator numbers and possibly a mix of the same. \\ | ||
2004-2006 covers also have a circled date stamp that was faded out for model season 2007. \\ | 2004-2006 covers also have a circled date stamp that was faded out for model season 2007. \\ | ||
Line 74: | Line 75: | ||
====== 2004-Up Cam Covers ====== | ====== 2004-Up Cam Covers ====== | ||
- | **Casting number change**: \\ | + | There are only 4 cam cover part number changes on 2004-2016 Sportsters, and most likely beyond and not counting XR models. \\ |
+ | They are the same cover with different finishes: polished, chrome, black or gray. \\ | ||
+ | The XR cover is a completely different design. \\ | ||
+ | Figuring that there was a casting/design change in 2007, that leaves a total of 2 versions of these covers not counting surface finish or XRs. \\ | ||
+ | |||
+ | **2007 Casting number change**: \\ | ||
The same casting design (25230-04) was used from 2004 through an early 2007 running design change to casting# (25230-04A). \\ | The same casting design (25230-04) was used from 2004 through an early 2007 running design change to casting# (25230-04A). \\ | ||
The casting number change has a direct correlation to the removal of casting bumps in the feed galley of the cover. \\ | The casting number change has a direct correlation to the removal of casting bumps in the feed galley of the cover. \\ | ||
Line 86: | Line 92: | ||
|{{:techtalk:evo:engmech:2007e_sportster_cam_cover-_inside_by_deadpartsmc.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:2007e_sportster_cam_cover-_inside_by_deadpartsmc.jpg?direct&300|}}| | ||
- | + | ===== 2004-E2007 Covers ===== | |
- | + | ||
+ | |{{:techtalk:evo:engmech:2004-e2007_sportster_cam_cover_25213-04_by_cyclepartsplus2013_pic1.jpg?direct&400|}} {{:techtalk:evo:engmech:2004-e2007_sportster_cam_cover_25213-04_by_cyclepartsplus2013_pic2.jpg?direct&400|}} | ||
+ | |||
+ | ===== L2007-Up Covers ===== | ||
\\ | \\ |