Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:priclutch02 [2022/07/15 05:57] ixl2relax [Removing the Primary Drive] |
techtalk:evo:priclutch02 [2022/09/14 00:17] ixl2relax [Quad-Ring - Clutch Inspection Cover] |
||
---|---|---|---|
Line 34: | Line 34: | ||
Over the years, the primary cover has been available in different finishes (polished Aluminum, rough Aluminum, Chrome, Black, etc.) with different part numbers for those variations. | Over the years, the primary cover has been available in different finishes (polished Aluminum, rough Aluminum, Chrome, Black, etc.) with different part numbers for those variations. | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ====== Quad-Ring - Clutch Inspection Cover ====== | ||
+ | |||
+ | From 1994-later the Clutch Inspection Cover (AKA: Derby Cover) has had a sealing ring, often referred to as the Quad-Ring. It is circular, but its cross-section profile is not round like an o-ring, but rather four-sided flat. The quad-ring P/N is 25463-94A.\\ | ||
+ | See discussion at http://xlforum.net/forums/showthread.php?t=1974683 | ||
+ | |||
+ | {{:techtalk:evo:priclutch:94-up-quad-ring-1-baby883.jpg?600|}}{{:techtalk:evo:priclutch:94-up-quad-ring-2-baby883.jpg?400|}} | ||
\\ | \\ | ||
Line 47: | Line 56: | ||
|{{:techtalk:evo:priclutch:primarychainadjuster-91-later.jpg|}}| | |{{:techtalk:evo:priclutch:primarychainadjuster-91-later.jpg|}}| | ||
- | |{{:techtalk:evo:priclutch:primarychainadjuster-compoldnew.jpg|}}| | + | |{{:techtalk:evo:priclutch:primarychainadjuster-compoldnew.jpg|}}| {{:techtalk:evo:priclutch:primarychainadjuster-nut-7804.jpg?200|}}\\ 1991-later Sportsters\\ Primary Chain Adjuster Nut\\ **P/N 7804**\\ This nut has a special\\ extended nylon face((http://xlforum.net/forums/showthread.php?t=1047928)) which\\ seals against the Primary Cover\\ \\ **TO PREVENT LEAKS**\\ Avoid Common Nylon-insert Nuts | |
- | | Upgrade 39975-90A should be used in place of 1991-2000 stock Chain Tensioner.\\ 2001-2003 models had the -90A part as factory OEM stock. ((photo by aswracing - http://xlforum.net/forums/showthread.php?t=1627892)) | | + | | Upgrade 39975-90A should be used in place of 1991-2000 stock Chain Tensioner.\\ 2001-2003 models had the -90A part as factory OEM stock. ((photo by aswracing - http://xlforum.net/forums/showthread.php?t=1627892)) | ::: | |
\\ | \\ | ||
Line 112: | Line 121: | ||
\\ | \\ | ||
- | {{techtalk:ref:tools:primary-brasshinge-lock.jpg?400|}} ((Scuba10jdl http://xlforum.net/forums/showthread.php?t=53268)) | + | {{techtalk:ref:tools:primary-brasshinge-lock.jpg?350|}} ((photo by Scuba10jdl (2002 883>1250) http://xlforum.net/forums/showthread.php?t=53268 - Post#98)) {{techtalk:evo:priclutch:primary-nuts.jpg?500|}} ((photo by IXL2Relax - 1994 883>1200)) |
\\ | \\ | ||
Line 136: | Line 145: | ||
A closed 4" BRASS hinge also works well to lock the sprockets and then you can use a pull bar and sockets / socket wrench. \\ | A closed 4" BRASS hinge also works well to lock the sprockets and then you can use a pull bar and sockets / socket wrench. \\ | ||
- | {{techtalk:ref:tools:primary-brasshinge-lock.jpg?300|}} ((photo by Scuba10jdl (2002 883>1250) http://xlforum.net/forums/showthread.php?t=53268 - Post#98)) {{techtalk:evo:priclutch:primary-nuts.jpg?400|}} ((photo by IXL2Relax - 1994 883>1200)) | + | {{techtalk:ref:tools:primary-brasshinge-lock.jpg?300|}} ((photo by Scuba10jdl (2002 883>1250) http://xlforum.net/forums/showthread.php?t=53268 - Post#98))\\ |
The threads should have previously been assembled with red Loctite. \\ | The threads should have previously been assembled with red Loctite. \\ |