Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ih:engctl02 [2020/03/09 09:48] – [Solenoid] ixl2relaxtechtalk:ih:engctl02 [2023/12/31 18:18] (current) – hippysmack
Line 41: Line 41:
  
 Reference these threads:\\ Reference these threads:\\
-http://xlforum.net/forums/showthread.php?t=1521782 - Dr. Dick Post#4 quoted above\\ +https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/140324-prestolite-hitachi-help?t=1521782 - Dr. Dick Post#4 quoted above\\ 
-http://xlforum.net/forums/showthread.php?t=1715008\\ +https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/159854-starter-motors?t=1715008\\ 
-http://xlforum.net/forums/showthread.php?t=1752598\\+https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/163098-starter-pipe-clearance?t=1752598\\
  
  
Line 54: Line 54:
 For additonal information, see the [[techtalk:evo:engctl02|Evo Section - Starter/Solenoid]] For additonal information, see the [[techtalk:evo:engctl02|Evo Section - Starter/Solenoid]]
  
-|  Prestolite Starter. ((photos by sifty of the XLFORUM http://xlforum.net/forums/showthread.php?t=1592463&page=27))  ||+|  Prestolite Starter. ((photos by sifty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/146604-first-harley-1975-xl1000-caf%C3%A9-project/page27?t=1592463&page=27))  ||
 |{{:techtalk:ih:engctl:prestolite_starter_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:prestolite_starter_11_by_sifty.jpg?direct&300|}}| |{{:techtalk:ih:engctl:prestolite_starter_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:prestolite_starter_11_by_sifty.jpg?direct&300|}}|
  
Line 65: Line 65:
 ====== Solenoid ====== ====== Solenoid ======
  
-{{ :techtalk:ih:engctl:72-xlh-startersolenoid-operation.jpg?400|}} +{{ :techtalk:ih:engctl:72-xlh-startersolenoid-operation.jpg?320|}} 
-A typical well-made solenoid as two windings connected to the small terminal. ((Oldwrench of the XLFORUM http://xlforum.net/forums/showthread.php?t=522413&page=2)) \\+A typical well-made solenoid as two windings connected to the small terminal. ((Oldwrench of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/74579-what-would-cause-the-solenoid-to-be-very-very-hot/page2?t=522413&page=2)) \\
 One coil (HOLD-IN) goes to solenoid case ground and the other (PULL-IN) goes to a big terminal (starter lead).\\ One coil (HOLD-IN) goes to solenoid case ground and the other (PULL-IN) goes to a big terminal (starter lead).\\
 When you hit the starter button, battery voltage goes thru the starter relay into the solenoid small terminal,\\ When you hit the starter button, battery voltage goes thru the starter relay into the solenoid small terminal,\\
Line 88: Line 88:
 Using an ohm meter would give really confusing readings because you'd see continuity to both case ground and the starter terminal from the solenoid windings connection. Using an ohm meter would give really confusing readings because you'd see continuity to both case ground and the starter terminal from the solenoid windings connection.
  
-67 and Up XLH Starter solenoid (71469-65) \\ +\\ 
-Below, the 1/4" solenoid mounting threads were stripped (nut on the top bolt) so they were tapped out for 8mm cap screws. ((photo by sifty of the XLFORUM http://xlforum.net/forums/showthread.php?t=1592463&page=27)) \\+ 
 +**67 and Up XLH Starter solenoid (71469-65)**\\ 
 +Below, the 1/4" solenoid mounting threads were stripped (nut on the top bolt) so they were tapped out for 8mm cap screws. ((photo by sifty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/146604-first-harley-1975-xl1000-caf%C3%A9-project/page27?t=1592463&page=27)) \\
 8mm x 1.25 threads have almost exactly the same thread pitch as the original 1/4" thread. \\ 8mm x 1.25 threads have almost exactly the same thread pitch as the original 1/4" thread. \\
-Then the mounting bracket and and spacer were drilled 8mm and the solenoid was installed using allen head cap screws and spring washers. \\+Then the mounting bracket and and spacer were drilled 8mm and the solenoid was installed using allen head cap screws and spring washers.
  
-|  Starter solenoid (71469-65) ((photo by sifty of the XLFORUM http://xlforum.net/forums/showthread.php?t=1592463&page=27))  |||+|  Starter solenoid (71469-65) ((photo by sifty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/146604-first-harley-1975-xl1000-caf%C3%A9-project/page27?t=1592463&page=27))  |||
 |{{:techtalk:ih:engctl:solenoid_switch_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:solenoid_switch_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:solenoid_switch_3_by_sifty.jpg?direct&300|}}| |{{:techtalk:ih:engctl:solenoid_switch_1_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:solenoid_switch_2_by_sifty.jpg?direct&300|}}|{{:techtalk:ih:engctl:solenoid_switch_3_by_sifty.jpg?direct&300|}}|
  
 \\ \\
- 
- 
  
 ===== Check Solenoid Cover for Conductivity ===== ===== Check Solenoid Cover for Conductivity =====

Trace: