Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:engmech01q [2019/02/18 04:05] hippysmack [OEM 2000 and Up vs SBC Lifters] |
techtalk:ref:engmech01q [2024/01/14 18:24] hippysmack |
||
---|---|---|---|
Line 4: | Line 4: | ||
====== Tappet Flats ====== | ====== Tappet Flats ====== | ||
**This is in consideration of induced noise from the use of high lift cams**. \\ | **This is in consideration of induced noise from the use of high lift cams**. \\ | ||
- | The factory lifter is up to the job from the point of view of the hydraulics. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1510606&page=2)) \\ | + | The factory lifter is up to the job from the point of view of the hydraulics. ((aswracing of the XLFORUM https://www.xlforum.net/forum/vendors/hammer-performance/139198-well-been-doing-some-thinking-excess-valvetrain-noise/page2?t=1510606&page=2)) \\ |
However, the factory lifter's weaknesses are lack of available travel and less durable axle bearings. \\ | However, the factory lifter's weaknesses are lack of available travel and less durable axle bearings. \\ | ||
It's possible to machine the flat longer on a stock lifter. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=341901)) \\ | It's possible to machine the flat longer on a stock lifter. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=341901)) \\ | ||
Line 15: | Line 15: | ||
In 2006, they changed the design to a plastic "anti-rotaion-device" or ARD. \\ | In 2006, they changed the design to a plastic "anti-rotaion-device" or ARD. \\ | ||
- | One thing you need to pay attention to when using high lift cams is the tappet pin clearance. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=322680)) \\ | + | One thing you need to pay attention to when using high lift cams is the tappet pin clearance. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=322680)) ((http://xlforum.net/forums/showthread.php?p=1011178&highlight=lifter+pins#post1011178)) \\ |
Without enough clearance, the tappet will contact the pin and make a racket. \\ | Without enough clearance, the tappet will contact the pin and make a racket. \\ | ||
The generally accepted minimum clearance is .060": | The generally accepted minimum clearance is .060": | ||
Line 87: | Line 87: | ||
High performance lifters are especially helpful as a piece of preventative maintenance when high spring pressures are used. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?s=73d24db8f0756ef41c6215fd92ad0055&p=4726240)) \\ | High performance lifters are especially helpful as a piece of preventative maintenance when high spring pressures are used. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?s=73d24db8f0756ef41c6215fd92ad0055&p=4726240)) \\ | ||
The longer flats also allow higher lifts. | The longer flats also allow higher lifts. | ||
+ | |||
===== Other Useful Links ===== | ===== Other Useful Links ===== | ||
Line 92: | Line 93: | ||
===== Feuling lifters ===== | ===== Feuling lifters ===== | ||
+ | |||
+ | |||
+ | |||
===== Gaterman Lifters ===== | ===== Gaterman Lifters ===== | ||
Four different models are available for XL's. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?s=73d24db8f0756ef41c6215fd92ad0055&p=4726240)) \\ | Four different models are available for XL's. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?s=73d24db8f0756ef41c6215fd92ad0055&p=4726240)) \\ |