Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:engmech07 [2020/10/08 23:31] hippysmack [Sub Documents] |
techtalk:ref:engmech07 [2020/11/03 21:27] hippysmack [OEM oil paths and engine breathing drawings] |
||
---|---|---|---|
Line 5: | Line 5: | ||
====== Engine Breathing ====== | ====== Engine Breathing ====== | ||
- | 57-76 engines have a different breathing cycle than 77-up engines. \\ | + | 57-76 engines have a different breathing cycle than 77-up engines. The end result is the same. However, the means to get there is different. \\ |
- | The end result is the same. However, the means to get there is different. \\ | + | |
Below are the two systems explained. \\ | Below are the two systems explained. \\ | ||
You can also reference the sub documents under each particle subject heading. These pages are more detailed information on certain subjects. \\ | You can also reference the sub documents under each particle subject heading. These pages are more detailed information on certain subjects. \\ | ||
Line 31: | Line 30: | ||
**Engine Breathing Cycle**: \\ | **Engine Breathing Cycle**: \\ | ||
+ | A mixture of crankcase air and oil mist is produced on each piston down stroke. \\ | ||
+ | Upstroke pulls this mixture up into suspension but in tiny particles to mix with the air moving around and thrown here to there for lubrication. \\ | ||
+ | The oil is separated from the air by way of collision. Everything the air/oil mix touches on the way to the vent separates some oil from the air. | ||
+ | |||
57-76 engines breath and scavenge oil from the same hole. \\ | 57-76 engines breath and scavenge oil from the same hole. \\ | ||
On piston down stroke, drain oil is pushed into the oil galley (slot) in the rear of the crankcase and toward the oil trap beside the breather gear. \\ | On piston down stroke, drain oil is pushed into the oil galley (slot) in the rear of the crankcase and toward the oil trap beside the breather gear. \\ | ||
- | When the breather window opens, both drain oil and crankcase air pressure are pushed into the rotating breather gear. \\ | + | When the breather window opens after downstroke, both drain oil and crankcase air pressure are pushed into the rotating breather gear. \\ |
- | The oil and air is slung out from the center of the gear into the gearcase. | + | The oil and air is slung out from the center of the gear into the gearcase where it bounces on cam gears, case walls, etc. \\ |
- | + | Air / oil mist flows toward the vent and the oil gets spun out of suspension by the oil slinger on the generator drive gear. \\ | |
- | The breather valve then closes on piston upstroke past BDC, creating vacuum in the crankcase. \\ | + | Crankcase exhaust air is then sent out the breather tube. \\ |
- | Crankcase exhaust air from the gearcase is sent out the breather tube. \\ | + | The breather valve then closes on after the pistons rise (after BDC), creating vacuum in the crankcase and the cycle repeats. \\ |
- | Any oil still in suspension with the air on the way to the breather tube is separated by an oil slinger on the generator drive gear. \\ | + | |
===== 1977-1985 ===== | ===== 1977-1985 ===== | ||
Line 60: | Line 62: | ||
Many cases of excess breather oil is caused by poorly functioning check valves. | Many cases of excess breather oil is caused by poorly functioning check valves. | ||
- | **Engine Breathing Cycle**: \\ | + | **Engine Breathing Cycle**: |
A mixture of crankcase air and oil mist is produced on each piston down stroke. \\ | A mixture of crankcase air and oil mist is produced on each piston down stroke. \\ | ||
- | Upstroke pulls oil up into suspension but in tiny particles to mix with the air moving around and thrown here to there for lubrication. \\ | + | Upstroke pulls this mixture up into suspension but in tiny particles to mix with the air moving around and thrown here to there for lubrication. \\ |
- | The oil is separated from the air by way of collision. \\ | + | The oil is separated from the air by way of collision. Everything the air/oil mix touches on the way to the vent separates some oil from the air. \\ |
- | Everything the air/oil mix touches on the way out separates some oil from the air. \\ | + | |
- | 77-up engines blow the air/oil mix into the gearcase where it bounces on cam gears, case walls, etc. and then gets spun out by the oil slinger. \\ | + | 77-up engines scavenge oil from down low in the crankcase and breath up higher through holes in the cam wall. \\ |
- | This helps to splash lube the moving parts in the engine when it is picked up and blown around. \\ | + | On piston downstroke, drain oil is pushed into the oil galley and crankcase air pressure is pushed into the gearcase and the breather valve is pushed open. \\ |
- | The oil mist is then separated from the crankcase air and the excess air pressure is vented out of the engine past the one way breather valve. \\ | + | The air/ oil mist is slung around in the gearcase where it bounces on cam gears, case walls, etc. \\ |
- | 77-85 engines vent through a valve in the cam cover. \\ | + | Remaining air / oil mist flows toward the vent. \\ |
+ | On 77-E84 engines, oil gets spun out of suspension by the oil slinger on the generator drive gear and crankcase exhaust air is then sent out the breather vent. \\ | ||
+ | On L84-85 engines, the slinger washer was removed and a breather baffle tube was installed in the cover to separate oil. \\ | ||
+ | Oil hits the breather baffler tube then the back side of the breather valve to separate from the air and drains back into the gearcase. \\ | ||
+ | The breather valve then closes at piston (BDC), creating vacuum in the crankcase as the piston rises and the cycle repeats. \\ | ||
There were several changes made of the valve itself, but they operate on the same principle as a one way breather valve. \\ | There were several changes made of the valve itself, but they operate on the same principle as a one way breather valve. \\ | ||
+ | ==== OEM oil paths and engine breathing drawings ==== | ||
+ | |||
+ | {{:techtalk:ref:engmech:1957-1971_sportster_crankcase_pressure_path_by_hippysmack.png?direct&500|}} ((drawing by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:ref:engmech:1972-1976_sportster_crankcase_pressure_path_by_hippysmack.png?direct&750|}} ((drawing by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:ref:engmech:1977-1985_sportster_crankcase_pressure_path_by_hippysmack.png?direct&500|}} ((drawing by Hippysmack)) \\ | ||
====== Engine Breather Valves ====== | ====== Engine Breather Valves ====== | ||
===== Sub Documents ===== | ===== Sub Documents ===== | ||
Line 78: | Line 91: | ||
* [[techtalk:ref:engmech07h|Oil Drainback and Supplemental Air Intake from Breather Valves]] | * [[techtalk:ref:engmech07h|Oil Drainback and Supplemental Air Intake from Breather Valves]] | ||
* [[techtalk:ref:engmech07i|Dissecting the 77-78 Breather (foo-foo) Valve (24634-77)]] | * [[techtalk:ref:engmech07i|Dissecting the 77-78 Breather (foo-foo) Valve (24634-77)]] | ||
+ | * [[techtalk:ref:engmech07j|Further Study of the 79-E82 Reed Valve]] | ||
* [[techtalk:ref:engmech07s|XR-750 8-Ball Breather Valve]] | * [[techtalk:ref:engmech07s|XR-750 8-Ball Breather Valve]] | ||
* [[techtalk:ref:engmech05|Breather Venting / Relocation]] (list of breathing mods and aftermarket breathers for 1977-up engines) | * [[techtalk:ref:engmech05|Breather Venting / Relocation]] (list of breathing mods and aftermarket breathers for 1977-up engines) | ||
Line 104: | Line 118: | ||
* [[techtalk:ref:engmech07b|Affects of the 45° Rod / Piston Arrangement]] | * [[techtalk:ref:engmech07b|Affects of the 45° Rod / Piston Arrangement]] | ||
* [[techtalk:ref:engmech07c|Differential Pressure]] | * [[techtalk:ref:engmech07c|Differential Pressure]] | ||
+ | * [[techtalk:ref:engmech04r|Air Pressure and Vacuum at Different Elevations]] | ||
* [[techtalk:ref:engmech07d|Blowby and Ring Seal]] | * [[techtalk:ref:engmech07d|Blowby and Ring Seal]] | ||
* [[techtalk:ref:engmech07f|Liquid Drag vs Fluid Drag]] | * [[techtalk:ref:engmech07f|Liquid Drag vs Fluid Drag]] | ||
Line 109: | Line 124: | ||
* [[techtalk:ref:oil20|Oil Tank Pressure]] | * [[techtalk:ref:oil20|Oil Tank Pressure]] | ||
* [[techtalk:ref:engmech04p|Vacuum Pump for Reducing Crankcase Pressure]] | * [[techtalk:ref:engmech04p|Vacuum Pump for Reducing Crankcase Pressure]] | ||
+ | * See also in the Sportsterpedia: | ||
+ | * [[techtalk:ih:oil01#transfer_valve_76_and_earlier|Transfer Valve]] | ||
==== In the crankcase air system ==== | ==== In the crankcase air system ==== | ||