Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:engmech07 [2020/10/09 01:33] hippysmack [1977-1985] |
techtalk:ref:engmech07 [2020/11/03 21:27] hippysmack [OEM oil paths and engine breathing drawings] |
||
|---|---|---|---|
| Line 36: | Line 36: | ||
| 57-76 engines breath and scavenge oil from the same hole. \\ | 57-76 engines breath and scavenge oil from the same hole. \\ | ||
| On piston down stroke, drain oil is pushed into the oil galley (slot) in the rear of the crankcase and toward the oil trap beside the breather gear. \\ | On piston down stroke, drain oil is pushed into the oil galley (slot) in the rear of the crankcase and toward the oil trap beside the breather gear. \\ | ||
| - | When the breather window opens, both drain oil and crankcase air pressure are pushed into the rotating breather gear. \\ | + | When the breather window opens after downstroke, both drain oil and crankcase air pressure are pushed into the rotating breather gear. \\ |
| The oil and air is slung out from the center of the gear into the gearcase where it bounces on cam gears, case walls, etc. \\ | The oil and air is slung out from the center of the gear into the gearcase where it bounces on cam gears, case walls, etc. \\ | ||
| Air / oil mist flows toward the vent and the oil gets spun out of suspension by the oil slinger on the generator drive gear. \\ | Air / oil mist flows toward the vent and the oil gets spun out of suspension by the oil slinger on the generator drive gear. \\ | ||
| Crankcase exhaust air is then sent out the breather tube. \\ | Crankcase exhaust air is then sent out the breather tube. \\ | ||
| - | The breather valve then closes on piston upstroke past BDC, creating vacuum in the crankcase and the cycle repeats. \\ | + | The breather valve then closes on after the pistons rise (after BDC), creating vacuum in the crankcase and the cycle repeats. \\ |
| ===== 1977-1985 ===== | ===== 1977-1985 ===== | ||
| Line 77: | Line 77: | ||
| There were several changes made of the valve itself, but they operate on the same principle as a one way breather valve. \\ | There were several changes made of the valve itself, but they operate on the same principle as a one way breather valve. \\ | ||
| + | ==== OEM oil paths and engine breathing drawings ==== | ||
| + | {{:techtalk:ref:engmech:1957-1971_sportster_crankcase_pressure_path_by_hippysmack.png?direct&500|}} ((drawing by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:ref:engmech:1972-1976_sportster_crankcase_pressure_path_by_hippysmack.png?direct&750|}} ((drawing by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:ref:engmech:1977-1985_sportster_crankcase_pressure_path_by_hippysmack.png?direct&500|}} ((drawing by Hippysmack)) \\ | ||
| ====== Engine Breather Valves ====== | ====== Engine Breather Valves ====== | ||
| ===== Sub Documents ===== | ===== Sub Documents ===== | ||
| Line 85: | Line 91: | ||
| * [[techtalk:ref:engmech07h|Oil Drainback and Supplemental Air Intake from Breather Valves]] | * [[techtalk:ref:engmech07h|Oil Drainback and Supplemental Air Intake from Breather Valves]] | ||
| * [[techtalk:ref:engmech07i|Dissecting the 77-78 Breather (foo-foo) Valve (24634-77)]] | * [[techtalk:ref:engmech07i|Dissecting the 77-78 Breather (foo-foo) Valve (24634-77)]] | ||
| + | * [[techtalk:ref:engmech07j|Further Study of the 79-E82 Reed Valve]] | ||
| * [[techtalk:ref:engmech07s|XR-750 8-Ball Breather Valve]] | * [[techtalk:ref:engmech07s|XR-750 8-Ball Breather Valve]] | ||
| * [[techtalk:ref:engmech05|Breather Venting / Relocation]] (list of breathing mods and aftermarket breathers for 1977-up engines) | * [[techtalk:ref:engmech05|Breather Venting / Relocation]] (list of breathing mods and aftermarket breathers for 1977-up engines) | ||
| Line 111: | Line 118: | ||
| * [[techtalk:ref:engmech07b|Affects of the 45° Rod / Piston Arrangement]] | * [[techtalk:ref:engmech07b|Affects of the 45° Rod / Piston Arrangement]] | ||
| * [[techtalk:ref:engmech07c|Differential Pressure]] | * [[techtalk:ref:engmech07c|Differential Pressure]] | ||
| + | * [[techtalk:ref:engmech04r|Air Pressure and Vacuum at Different Elevations]] | ||
| * [[techtalk:ref:engmech07d|Blowby and Ring Seal]] | * [[techtalk:ref:engmech07d|Blowby and Ring Seal]] | ||
| * [[techtalk:ref:engmech07f|Liquid Drag vs Fluid Drag]] | * [[techtalk:ref:engmech07f|Liquid Drag vs Fluid Drag]] | ||
| Line 116: | Line 124: | ||
| * [[techtalk:ref:oil20|Oil Tank Pressure]] | * [[techtalk:ref:oil20|Oil Tank Pressure]] | ||
| * [[techtalk:ref:engmech04p|Vacuum Pump for Reducing Crankcase Pressure]] | * [[techtalk:ref:engmech04p|Vacuum Pump for Reducing Crankcase Pressure]] | ||
| + | * See also in the Sportsterpedia: | ||
| + | * [[techtalk:ih:oil01#transfer_valve_76_and_earlier|Transfer Valve]] | ||
| ==== In the crankcase air system ==== | ==== In the crankcase air system ==== | ||
