Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:oil13 [2021/06/16 03:33]
hippysmack [In-Tank to External Spin-on Filter Conversion and Plumbing for Ironheads]
+++ techtalk:ref:oil13 [2024/01/19 01:38]
hippysmack
@@ Line 2: / Line 2: @@
 ====== REF: Oiling & Lubrication ======
 ====== Remote Oil Filters ======
-The stock oil filter (HD 63782-80T) is the small one that is usually used on custom bikes. Chrome or black can be found. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=563241)) \\
+The stock oil filter (HD 63782-80T) is the small one that is usually used on custom bikes. Chrome or black can be found. ((IronMick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/78212-67-ironhead-oil-routing?t=563241)) \\
 However, it is also commonly known that the more oil you hold, the more motor heat can be transferred to dissipate that heat. \\
-Race bikes have huge oil tanks for that reason. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=563241)) \\
+Race bikes have huge oil tanks for that reason. ((Monte03 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/78212-67-ironhead-oil-routing?t=563241)) \\
 If you go the filter route, be sure to purge the lines by bleeding the pump front nipple first while running. \\
 Then take the return line and place it into a pail before you connect to the barb tank fitting so you assure a complete circle has been made.
 ====== Plumbing to Oil Filter ======
 **Note**: On all spin on oil filters, dirty oil goes in the outside of the filter. Clean oil comes out the center. (( ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?p=5643382&highlight=oil+filter+bracket#post5643382)) \\
 If you are not sure, start the motor momentarily with the filter off and if oil is pumped out the center port, you have it backwards.
@@ Line 30: / Line 29: @@
 ====== Parts / Kits ======
 Below is a parts list for a remote oil filter setup although it's not a kit per say; ((HolyHandGrenade of the XLFORUM http://xlforum.net/forums/showthread.php?t=1189337)) \\
 Derale spin-on bypass adapter with dual 1/2" NPT ports. ((https://www.jegs.com/i/Derale/259/15703/10002/-1)) \\
@@ Line 74: / Line 72: @@
 \\
 ===== On the left motor mount =====
 The OEM filter is mounted on the lower left front engine mount on 82-E84 models. \\
 This has also been a popular practice on earlier bikes. \\
@@ Line 89: / Line 86: @@
 ===== Other forward positions =====
 |  This one sets the filter upside down. ((photos by chief of the XLFORUM http://xlforum.net/forums/showthread.php?t=897611))  ||
 |{{:techtalk:ref:oil:motor_mount_filter_adapter_1_by_chief.jpg?direct&300|}}|{{:techtalk:ref:oil:motor_mount_filter_adapter_2_by_chief.jpg?direct&300|}}|
@@ Line 113: / Line 109: @@
 ===== Rear mounted filters =====
 |  Custom built oil filter mount. ((photos by dm4x4 of the XLFORUM http://xlforum.net/forums/showthread.php?t=897611))  |||
 |{{:techtalk:ref:oil:custom_oil_filter_mount_1_by_dm4x4.jpg?direct&300|}}|{{:techtalk:ref:oil:custom_oil_filter_mount_2_by_dm4x4.jpg?direct&300|}}|{{:techtalk:ref:oil:custom_oil_filter_mount_3_by_dm4x4.jpg?direct&300|}}|
@@ Line 142: / Line 137: @@
 \\
 ===== Modifying a standard motor mount for use as a oil filter mount =====
   * This can be done on the bike but it's easier to remove the motor mount and do the work on the bench. ((bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=1266793)) \\
   * **Simplified version**:
@@ Line 218: / Line 212: @@
 ===== Build Your Own Motor / Oil Filter Mount =====
 Article by sifty of the XLFORUM ((http://xlforum.net/forums/showthread.php?page=22&t=1592463)) \\
@@ Line 273: / Line 266: @@
 |{{:techtalk:ref:oil:homemade_oil_filter_mount_16_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_oil_filter_mount_17_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_oil_filter_mount_18_by_sifty.jpg?direct&300|}}|
+====== S&S Oil Filter Mount (1986-1990) ======
+This billet oil filter mounting bracket (751510) fits any generator engine with 5/16" generator mounting holes and replaces the OEM 1986-1990 Sportster filter pad. ((https://catalog.zodiac.nl/en/19-oil-tank-filter-line/oil-filter/s-s-oil-filter-mount-5335)) \\
+The oil filter bracket seals off the cam chest and provides a convenient place for a spin-on oil filter. \\
+The bracket is machined for easy routing of an oil cooler in all applications and accepts the stock oil pressure sending switch. \\
+It does not have an oil pressure regulator built into it like the OEM filter pad does. ((A 4 liter V8 eater of the XLFORUM http://xlforum.net/forums/showthread.php?t=1359577&page=88)) \\
+|  S&S oil filter mount. ((photos by A 4 liter V8 eater of the XLFORUM http://xlforum.net/forums/showthread.php?t=1359577&page=89))  ||
+|{{:techtalk:ref:oil:oil_filter_mount_sands_1986-1990_pic1_by_a_4_liter_v8_eater.jpg?direct&300|}}|{{:techtalk:ref:oil:oil_filter_mount_sands_1986-1990_pic2_by_a_4_liter_v8_eater.jpg?direct&300|}}|
 \\
 [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]

Trace:

Differences

Navigation

Search

Toolbox