REF: Suspension - Sub-02C - Sportsterpedia

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: Suspension - Sub-02C ======
{{common:space100x5px.jpg?650|}}[[techtalk:ref:susp02|Back to 'Front Fork Info']]

===== Front Forks - Refinishing Aluminum Sliders =====

This information comes from an XLForum thread: https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/203388-slider-repair?t=2080639\\
Some editing done on the comments. Photos are by 'joe s'.

**Comments by joe s - Describing his finishing process**\\
If the pits aren't too too bad, you can sand them and re-clear. On my FXR project, I disassembled the forks, but I don't see why you can't do this on the bike with the wheel and fender removed.

This is what they looked like:\\

{{:techtalk:ref:susp:forkrefinish01-joe_s.jpg?600|}}

I cleaned everything with acetone first, and that started removing the factory clear coat. Perfect, because it left the original finishes that I can match after repairing the scratch marks and oxidation spots. I dressed them with a dremel on slow speed. Letting the stone bounce at the very end, sort of reproduced the surface, but not well.

They look like they have a skin condition.\\
{{:techtalk:ref:susp:forkrefinish02-joe_s.jpg?600|}}

Looking at the factory shiny areas, there are fine sanding marks, so first I tried 400 grit, and that removed the stains, but was too coarse. 600 grit was closer, but 1000 grit was just right.

You can see what I mean by rough and smooth areas.\\
{{:techtalk:ref:susp:forkrefinish03-joe_s.jpg?600|}}

Make sure they are really clean again, wiping with acetone until the rag is clean. I use NAPA Tec Base clear in a rattle can, it holds up well and stayed clear on my 79 FXS for years, including the rocker covers:\\
{{:techtalk:ref:susp:forkrefinish04-joe_s.jpg?600|}}

Good luck, your mileage may vary.

**Comments by SHAKY DAVE**\\
Absolutely nice work. Since I do the paint and body work on restoration cars, step sanding is the way to go. I sand aluminum starting with 600 going up from there with 1000,1500,2000,3000 to 5000. Pretty shiny then, but I normally buff the parts and dont use any clear on anything. The buffed parts on my 2 ironheads are still great after 11 years. Some Mother's aluminum polish takes care of keeping parts lookin good, but only when i feel like doin it - hahaha.

**Comments by brucstoudt**\\
I had the same problem with my '03. It was caused by salt air corrosion from being in Florida. Most of the damage was in the front area in the windstream. I fixed mine on the bike by wet sanding them with 1500 wet or dry paper then polishing them. I have a brick of aluminum polishing compound that I load on my polishing buff. The sliders come from the factory with a clear coating on them that has to be sanded through to get down to the aluminum. I will not reclear them.

\\

\\

[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]\\
[[techtalk:ref:susp02|Back to 'Front Fork Info']]
Trace: • EVO: Engine Mechanicals - Sub-01A • REF: Suspension - Sub-02C • REF: Engine Mechanicals - Sub-05G
Navigation

Search

Toolbox
