Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:tools116 [2018/05/21 07:47] ixl2relax ↷ Page name changed from techtalk:ref:tools01-016 to techtalk:ref:tools116 |
techtalk:ref:tools116 [2024/01/23 15:02] hippysmack |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== REF: Tools - Sub-016 ====== | + | ====== REF: Tools - 116 ====== |
+ | ====== Engine Sprocket and Clutch Removal / Installation ====== | ||
+ | A reversible impact wrench has been used successfully to remove both the engine sprocket and the clutch basket nut. \\ | ||
+ | However, it's been debatable whether you can accurately install them back to proper torque without using a torque wrench instead. \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:engine_sprocket_removal_-_installation_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/169896-2000-883-stator-replacement?t=1823130)) {{:techtalk:ref:tools:clutch_nut_removal_by_tigercreek.jpg?direct&300|}} ((photo by tigercreek of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/169896-2000-883-stator-replacement?t=1823130)) \\ | ||
====== Engine and Clutch Sprocket Locking Tools ====== | ====== Engine and Clutch Sprocket Locking Tools ====== | ||
Line 13: | Line 19: | ||
|{{techtalk:ref:tools:clutch_locking_tool_4_by_hopper.jpg?direct&300|}}|{{techtalk:ref:tools:clutch_locking_tool_5_by_hopper.jpg?direct&300|}}|| | |{{techtalk:ref:tools:clutch_locking_tool_4_by_hopper.jpg?direct&300|}}|{{techtalk:ref:tools:clutch_locking_tool_5_by_hopper.jpg?direct&300|}}|| | ||
^ Clutch Sprocket Locking Tools ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=2)) ^^^ | ^ Clutch Sprocket Locking Tools ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=2)) ^^^ | ||
+ | |||
+ | |{{:techtalk:ref:tools:primary_locking_tool_by_campsurf.jpg?direct&300|}}|{{:techtalk:ref:tools:1976-earlier_sportster_sprocket_locking_tool_97200-55_by_johngoober.jpg?direct&300|}}|{{:techtalk:ref:tools:primary_locking_tool_specs_by_67170.jpg?direct&300|}}| | ||
+ | ^ Primary Locking Tool ((photo by Campsurf of the XLFORUM http://xlforum.net/forums/showthread.php?t=1562755)) ^ 1976-Earlier Sportster \\ Sprocket Locking Tool (97200-55) ((photo by Ebay seller, johngoober, [[https://www.ebay.ca/sch/i.html?item=144998065911&rt=nc&_trksid=p2047675.m3561.l2562&_ssn=johngoober|Link to Ebay Store]] )) ^ 1976-Earlier Sportster \\ Sprocket Locking Tool (97200-55) Specs ((photo by 67170 of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=14)) ^ | ||
===== 5 Speed ===== | ===== 5 Speed ===== | ||
+ | Any of these 'wedges' can be used but be sure not to put pressure on the shifter shaft with them. \\ | ||
+ | |{{techtalk:ref:transfinal:engine-clutch_sprocket_locks_by_vafish.jpg?direct&300|}}|{{techtalk:ref:tools:primary-brasshinge-lock.jpg?300|}}| | ||
+ | |A heavy duty 4" door hinge works well. \\ A cheap 4" door hinge bends like a pretzel. \\ The derilin block just gets shredded up. \\ But, the heavy duty 4" hinge works great. ((VaFish http://xlforum.net/forums/showthread.php?t=1997193))|A closed 4" BRASS hinge also works well. ((photo by Scuba10jdl of the XLFORUM http://xlforum.net/forums/showthread.php?t=53268))| | ||
- | |{{techtalk:ref:transfinal:engine-clutch_sprocket_locks_by_vafish.jpg?direct&300|}}| | + | |{{techtalk:ref:svcproc:sprocketholdingtool_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:tools:sprocketholdingtool_2_by_hippysmack.jpg?direct&300|}}| |
- | |A heavy duty 4" door hinge works well. \\ A cheap 4" door hinge bends like a pretzel. \\ The derilin block just gets shredded up. \\ But, the heavy duty 4" hinge works great. ((VaFish http://xlforum.net/forums/showthread.php?t=1997193))| | + | |
- | + | ||
- | |{{techtalk:ref:tools:sprocketholdingtool_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:tools:sprocketholdingtool_2_by_hippysmack.jpg?direct&300|}}| | + | |
| Home made sprocket lock 4.19" x 1.5" x 5/16" steel with beveled edges ((photos by Hippysmack http://xlforum.net/forums/showthread.php?t=1848977)) || | | Home made sprocket lock 4.19" x 1.5" x 5/16" steel with beveled edges ((photos by Hippysmack http://xlforum.net/forums/showthread.php?t=1848977)) || | ||
+ | |||
+ | \\ | ||