Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools140 [2018/10/21 19:16] hippysmack [Getting the Right Dial Indicator] |
techtalk:ref:tools140 [2018/11/01 18:28] hippysmack [Tool Posts / Indicator Holders] |
||
---|---|---|---|
Line 41: | Line 41: | ||
|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_12_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_12_by_hippysmack.jpg?direct&300|}}| | ||
- | |Tape the inside of the cover, then cut around it. Remove the circle piece of tape from the cover, place the sticky side up on the back of the indicator. \\ Then tape that down. This keeps the sticky side from getting stuck on internal moving parts.||| | + | |Tape the inside of the cover, then cut around it. Remove the circle piece of tape from the cover, place the sticky side up on the back of the indicator. \\ Then tape that down. This keeps the sticky side from getting stuck on internal moving parts. ((photos by Hippysmack))||| |
|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_10_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_9_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_10_by_hippysmack.jpg?direct&300|}}| | ||
|Make sure to leave enough on the sides to hold down the temporary tape backing. \\ Now this indicator can be used in the lifter hole. ((photos by Hippysmack))|| | |Make sure to leave enough on the sides to hold down the temporary tape backing. \\ Now this indicator can be used in the lifter hole. ((photos by Hippysmack))|| | ||
|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_11_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_13_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_11_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:indicator_mod_for_degreeing_cams_13_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |||
+ | |||
+ | ====== Tool Posts / Indicator Holders ====== | ||
+ | ^Homemade indicator holder from Nylon flat stock ((photos by Hippysmack))^ | ||
+ | |{{:techtalk:ref:tools:dial_indicator_holder_1_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |||
+ | ^Homemade indicator tool post from scrap steel and aluminum ((photos by Hippysmack))^ | ||
+ | |{{:techtalk:ref:tools:dial_indicator_post_6_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |{{:techtalk:ref:tools:dial_indicator_post_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:dial_indicator_post_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:dial_indicator_post_3_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |{{:techtalk:ref:tools:dial_indicator_post_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:dial_indicator_post_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:dial_indicator_post_1_by_hippysmack.jpg?direct&300|}}| | ||