Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:tools151 [2018/11/06 22:07] hippysmack [Pin Vise] |
techtalk:ref:tools151 [2020/04/28 23:00] hippysmack ↷ Links adapted because of a move operation |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== REF: Tools - 151 ====== | ====== REF: Tools - 151 ====== | ||
| ====== Drills, Bits and Accompaniments ====== | ====== Drills, Bits and Accompaniments ====== | ||
| + | See also in the Sportsterpedia: | ||
| + | |||
| + | * [[techtalk:ref:genmsr11|Cutting Oils, Soaking Oils and Lubes]] | ||
| + | * [[techtalk:ref:tools030#general_drilling_and_tapping|General Drilling and Tapping]] | ||
| ====== Left Hand Drill Bit ====== | ====== Left Hand Drill Bit ====== | ||
| Line 16: | Line 20: | ||
| ^Left Hand Drill Bit ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?page=3&t=1836654))^ | ^Left Hand Drill Bit ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?page=3&t=1836654))^ | ||
| + | ====== Pilot Point Drill Bit ====== | ||
| + | These bits have a built in 'center bore' on the end. \\ | ||
| + | It cuts center first and the fluted cutter comes in to cut the primary hole. \\ | ||
| + | This helps to keep the bit from wandering and keep the hole centered throughout the cut. \\ | ||
| + | |||
| + | |{{:techtalk:ref:tools:3-16_pilot_drill_bit_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:3-16_pilot_drill_bit_2_by_hippysmack.jpg?direct&300|}}| | ||
| ====== Pin Vise ====== | ====== Pin Vise ====== | ||
| A pin vise is made for holding tiny drill bits. \\ | A pin vise is made for holding tiny drill bits. \\ | ||
| Line 25: | Line 35: | ||
| ^Pin vise made to fit into a regular drill chuck ((photo by piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=1251451&page=6))^ | ^Pin vise made to fit into a regular drill chuck ((photo by piniongear of the XLFORUM http://xlforum.net/forums/showthread.php?t=1251451&page=6))^ | ||
| + | \\ | ||
| + | |||
| + | * This hand held one has a swivel head and was purchased at Hobby Lobby for about $10. ((https://www.hobbylobby.com/Crafts-Hobbies/Hobbies-Collecting/Tools-Blades/Swivel-Head-Pin-Vise/p/25368)) | ||
| + | * Comes with two double-end collets to hold a range of drills from #80 (.0135) to #30 (.1285). | ||
| |{{:techtalk:ref:tools:pin_vise_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:pin_vise_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:pin_vise_3_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:tools:pin_vise_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:pin_vise_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:pin_vise_3_by_hippysmack.jpg?direct&300|}}| | ||
| - | ^ Hand held pin vise with a reversible collet for bigger drill bits ((photo by Hippysmack)) ^^^ | + | ^ Testor hand held pin vise with a reversible collet for bigger drill bits ((photos by Hippysmack)) ^^^ |
| ====== Hole Saw ====== | ====== Hole Saw ====== | ||
| A hole saw is not just used for door knob installation. \\ | A hole saw is not just used for door knob installation. \\ | ||
