Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ref:tools168 [2019/09/11 05:20] – [Uses] hippysmacktechtalk:ref:tools168 [2023/11/04 19:10] (current) – [Bulb Type Pressure Tester] hippysmack
Line 1: Line 1:
 [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]] [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
-====== REF: Tools - 167 ====== +====== REF: Tools - 168 ====== 
-====== Dremil Type Rotary Tool ====== +====== Bulb Type Pressure Tester ====== 
-A Dremil tool has many uses from cutting to polishing metal. Always wear a face shield when using this tool. \\ +Below is a bulb type pressure tester for testing the carburetor needle seat valve as referenced in TSB #564. \\ 
-It operates at a very high speed and tiny pieces of the cutting bits and the metal will hit your eyes faster than you can blink. \\ +It's for use in testing the seat valve of Tillotson carburetors used on 1966-later Sportsters and 1967-later Electra Glides. \\ 
-It's good for cutting carbon & stainless steel, shortening bolts, shaping metal projects etc. \\+[[techtalk:miscres:miscres05#tsb_550-599|Click Here]] to go to the TSB page, scroll down and click on the "Y" next to TSB #564 to download the bulletin. \\ 
 +The bulletin was an attempt by the MoCo to diagnose a simple needle/seat issue and replace if needed at the dealer level. \\ 
 +(instead of sending the carb back to the factory for a warranty claim) \\
  
-{{:techtalk:ref:tools:dremel_tool_by_graywolf.jpg?direct&300|}} ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3)) \\ +This bulb tester is HD (94750-68). \\ 
- +Per the service bulletin. it's installed on the fuel inlet fitting with the vent plugged. \\ 
-====== Uses ====== +Squeezing the bulb adds pressure to the inlet and the gauge shows how much is added. \\ 
- +A moistened needle and seat should hold app. 1 to 1·1/2 psi and release at approximately 3 to 5 psi. \\ 
-|Cutting slots in pipes for shields. ((photo by Graywolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=2070881&page=3))|  Shortening a bolt. ((photos by Hippysmack))  || +A dry needle and seat will not hold as well as a moist one. \\ 
-|{{:techtalk:ref:tools:heatshield_strap_by_graywolf.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:shortening_a_bolt_2_by_hippysmack.jpg?direct&300|}}| +The gauge is for low pressure (15psi max) which shows a more accurate reading than higher pressure gauges. \\
-|+
  
 +Here is the bulb tester. Click on any pic to enlarge: \\
  
 +|  HD Needle-Seat Bulb-Type Leak Tester (94750-68) ((photos courtesy of Ebay seller; cdchoppa. [[https://www.ebay.com/str/cdchoppa?_trksid=p4429486.m145687.l149086|Link to Ebay Store]] ))  |||
 +|{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic1_by_cdchoppa.jpg?direct&300|}}|{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic2_by_cdchoppa.jpg?direct&300|}}|{{:techtalk:ref:tools:leak_tester_94750-68_needle-seat_bulb-type_pic3_by_cdchoppa.jpg?direct&300|}}|
  
 \\ \\
  
 [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]
- 
  

Trace: • REF: Tools - 127 • REF: Tools - 140 • REF: Tools - 101