[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] ====== EVO: Transmission & Final Drive ====== \\ ====== Primary/Transmission/Final Gear Ratios ===== {{techtalk:evo:transfinal:sportster-ptf-gearratios-1986-2016-us.jpg?direct&}} \\ ====== 883 Belt Model Trans Sprocket Part Numbers ====== **1991-92 883 Deluxe**\\ **1993-94E 883 All** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | Sprkt Kit w/mtg parts | | Part # | 12050 | 33334-85 0.849" Thick | Only-In-Kit>> | 40022-91 128T 1-1/8" | 40285-91A 27T | | As a set, the seal, spacer & sprocket from 1995 can be retrofitted back to the 1991-94 models. |||||| **1994L-2003 883 All** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | Sprkt Kit w/mtg parts | | Part # | 12067A | 33344-94 0.600" Thick | 40288-95 27T | 40022-91 128T 1-1/8" | 40285-91B 27T | **2004-06 883 All** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | | Part # | 12067B | 33344-94 0.600" Thick | 40379-04 28T | 40570-04B 136T 1-1/8" | **2007-2010 - 883** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | | Part # | 12074 | Built into Bearing | 40379-04 28T | 40371-07 136T 1" | **2011+ - 883** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | | Part # | 12074 | Built into Bearing | 40409-04 29T | 40591-07 137T 1" | ====== 1200 Belt Model Trans Sprocket Part Numbers ====== **1991-94E - 1200** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | Sprkt Kit w/mtg parts | | Part # | 12050 | 33334-85 0.849" Thick | Only-In-Kit>> | 40022-91 128T 1-1/8" | 40202-91A 29T | | As a set, the seal, spacer & sprocket from 1995 can be retrofitted back to the 1991-94 models. |||||| **1994L-03 - 1200** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | Sprkt Kit w/mtg parts | | Part # | 12067A | 33344-94 0.600" Thick | 40205-95 29T | 40022-91 128T 1-1/8" | 40202-91B 29T | **2004-06 - 1200** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | | Part # | 12067B | 33344-94 0.600" Thick | 40409-04 29T | 40571-04B 137T 1-1/8" | **2007+ - 1200** | Part | Oil Seal | Spacer | Trans Sprocket | Belt | | Part # | 12074 | Built into Bearing | 40409-04 29T | 40591-07 137T 1" | \\ ====== Rear Belt Driven Sprocket Part Numbers ====== __**For 1991-1999 - OEM 61T Sprockets**__ **40213-91** is 61T BLACK **40227-93** is 61T SILVER **40246-91** is a casting number - These casting numbers are on both early, 1991-1999, and late, 2000-2003, Sportster 61 tooth x 1-1/8" pulleys. The offset is the same for early and late but The early and late are not interchangeable; the early has a 2" center hole, the late is 2-3/16". There are adapters available so you can use a late (2-3/16") on an early wheel (2") , but the early does not fit the late. You can tell the late pulley visually by looking at the machined bosses for the mounting bolts. The late model bosses are intruded by the center hole and do not show completely round. The early pulleys either have no bosses or the bosses are completely round. The early pulleys are silver, the late are silver or black, from the factory.((Sirrom1 - https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-drivetrain/sportster-motorcycle-transmission-clutch-primary-secondary-drive/188245-rear-sprocket?t=2005973)) \\ __**For 2000-2003 - OEM 61T Sprockets**__ **40213-00** is 61T BLACK **40227-00** is 61T SILVER \\ __**For 2004-2006 - OEM 61T Sprockets**__ **40350-04** is 68T BLACK **40352-04** is 68T SILVER \\ __**For 2007-2015 - OEM 61T Sprockets**__ **40350-07** is 68T BLACK w/highlights\\ **40444-07** is 68T BLACK (Nightster / 883 Iron)\\ **40353-08** is 68T BLACK (883 Iron / 48) \\ __**For 2016-2022 - OEM 61T Sprockets**__ **40350-07** is 68T BLACK w/highlights\\ **40444-07** is 68T BLACK (Nightster)\\ **42200121** is 68T BLACK (48) \\ ====== Final Drive Trans Belt Sprocket Issues (Differences between 1991, 1995 & 2004) ===== Remember, the Final Drive Trans Belt Sprocket has left-hand threads! Use a locking tool when removing or installing the sprocket. The Final Drive Trans Belt Sprocket (from the transmission) must align with the Rear Wheel Sprocket, which is determined by the wheel width. The Trans Drive Sprocket has a belt guide flange on one side only. | For 1991-2003 the sprocket flange is away from the engine. But, there\\ are spline differences between 1991-1994 and 1995-2003. | For 2004-later the sprocket flange is near the engine. | | {{:techtalk:evo:transfinal:finaldrivesprocket-1992-erik.jpg?400|}}((photo by Erik https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/70015-neutral-lamp-staying-on?t=472579)) | {{:techtalk:evo:transfinal:finaldrivesprocket-2005.jpg?382|}} | Pre-2004, on the outer flanged side, the center mounting splines are relatively flush with the flange face. But, on the engine side of the sprocket, the center mounting splines are recessed from the edge of the belt drive face. On 2004-later, the flange is on the engine side (with recessed splines there) and the mounting nut and lock plate are on the outer, flangeless, side. On 1991-94 Sportsters, the flanged side of the sprocket is away from the engine. On the opposite side, between the case bearing seal (for the transmission Final Drive Shaft) and the recessed splines on the Trans Drive Sprocket, is a spacer to fit in that recess. The width of the splines in contact with the Final Drive Shaft is 0.500". On the 1995-03 models, the center spline contact area of the Trans Drive Sprocket (on the Trans Drive Shaft) was widened to 0.766" and the recess spacer was reduced accordingly. The flanged side of the sprocket is still away from the engine. (As a set, the seal, spacer & sprocket from 1995 can be retrofitted back to the 1991-94 models.) Note: To fit a 1995-03 pulley to a 1991-1994 model requires the matching seal. The '95+ spacer has a larger outside diameter than the 1991-94. Also note, that 1994 was a transition year to the later style pulley; "early" '94s had "early" pulley setups, "late" '94s had '95+ pulley setups. On the 2004-later models, the Trans Drive Sprocket design was reversed. The flanged side was placed toward the engine, thereby pushing the usable belt surface farther away from the engine to allow for a wider rear tire (150mm). On the flanged side, the center mounting splines are recessed .400" from the flange face. For 2004-2005, the older spacer (as used on '95-'03) was still used between the case bearing seal and the sprocket. On the 2006+ models, the spacer was incorporated into the transmission output shaft bearing. | Year | Description & P/N || Note | | 1991-E94 | Oil Seal | 12050 | Spacer for Sprocket with\\ 0.500 width splines | | ::: | Spacer | 33334-85 | ::: | | L94-1995-2005 | Oil Seal | 12067B | Spacer for Sprocket with\\ 0.766 width splines | | ::: | Spacer | 33344-94 | ::: | | 2006-later | Oil Seal | 12074 | Spacer is part of\\ shaft bearing | | ::: | Spacer | 8964 | ::: | Note: The early trans pulleys will not mount to the '04-up's (even with the flange turned inboard) because: * 1) the "extra" 1/4" for the inner spline is only a "bump", there is no area for the nut and lockplate on the early versions. * 2) The splines need to be recessed .400" from the (now inboard) belt flange - they are not recessed on the early versions. * 3) With the flange outboard, the early version Final Trans Drive Sprocket cannot be properly aligned with the 2004+ Rear Wheel Sprocket. If the belt rides against the flange, overheating may occur and the flange (press fitted) can separate from the sprocket. This [[https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-drivetrain/sportster-motorcycle-transmission-clutch-primary-secondary-drive/179795-front-pulley-mods-final-drive?t=1931756|XLForum Thread]] was used for collecting the above information. Thanks to those who contributed, especially Sirrom1. \\ ====== Belt Sizes & Part Numbers ===== | Year | PartNo | Models | Description | | Chains --- 530 Final Drive Chain - 530 means Pitch = 5x 1/8" & Width = 3x 1/8" |||| | 1986-87 | | 883/1100 | 106 Links | | 1988-90 | | 883/1200 | 108 Links - 1/2" longer Swingarm | | 1991-92 | | 883 Std/Hug | 108 Links - 1/2" longer Swingarm | | | 40028-15E | 883/1100/1200 | Duckworth Brand 530 Chain | | ::: | ::: | Chain is 110 Links Long - Needs shortened to 106 or 108 Links\\ 40053-65 Duckworth Connecting Link || | | 40029-15E | 883/1100/1200 | Diamond Brand 530 Chain | | ::: | ::: | Chain is 110 Links Long - Needs shortened to 106 or 108 Links\\ 40052-65 Diamond Connecting Link || | |||| | Year | PartNo | Models | Description | | 1-1/8" Belt Width |||| | 1991-92 | 40022-91 | 883Dlx/1200 | 128 Tooth | | 1993-2003 | 40022-91 | 883/1200 | 128 Tooth | | 2004-2006 | 40570-04 | 883 | 136 Tooth | | | 40571-04B | 1200 | 137 Tooth | | 1" Belt Width |||| | 2007-2010 | 40371-07 | 883 | 136 Tooth | | | 40591-07 | 1200 | 137 Tooth | | 2011-2022 | 40591-07 | 883/1200 | 137 Tooth | \\ ====== Belt Twist for Carrying Spare Belt ====== | According to Sportsterpaul (of the XLForum) it is worth carrying a spare\\ belt for any long trip. When you replace a high mileage belt, save the\\ old one for a spare.((https://www.xlforum.net/showthread.php?t=14871 - Post#600)) Make a note of the rotation direction.\\ \\ Then, carefully, do a double twist of the belt to stack it three layers high.\\ It keeps a nice big radius (not damaging the belt) and packs well.\\ \\ **If your present belt should break, having a spare belt with you\\ can work for a roadside repair, without fully removing your tire.** \\ \\ The suggested way to replace the belt((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-drivetrain/sportster-motorcycle-transmission-clutch-primary-secondary-drive/46792-drive-belt-alternatives-for-emergencies?t=174407)) is to remove the lower bolt from\\ the shock and swing it out of the way. Loosen the axle nut and the axle\\ adjusters so the tire can move forward.\\ \\ Slip the belt up and over the belt guard, over the front sprocket, then onto\\ the rear sprocket from behind.\\ \\ Push the tire back and readjust the adjusters & tighten the axle.\\ Then align the shock and replace the lower bolt. | {{:techtalk:evo:transfinal:drivebelt-doubletwist-compact-sportsterpaul.jpg?400|}} | | You could also shortcut the procedure (if you dare to do so carefully). Don't loosen the axle or adjusters. Just remove the lower bolt from the shock\\ & swing it out of the way. Slip the belt up and over the belt guard, allowing it to be low behind the rear sprocket (not on it). Then slip the belt over\\ the front sprocket & start it (as far as possible) over the rear sprocket rim at the bottom. Pull it up snug to stay in place. Then roll the bike forward\\ so the belt pulls up around the rear sprocket and 'slips' into place. Replace the shock & bolt. The old belt will likely be a little loose from wear\\ and will 'slip on' in this way as a 'temporary' fix until you can replace it with a new belt. Or, do it the longer way if you have any concerns. || \\ ====== Aftermarket Options ===== Various aftermarket options are listed in the REFerence Section: [[techtalk:ref:transfinal01|HERE]] \\ [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]