One thing to remember is the temp reading at the oil tank and the actual highest oil temp in the engine are not the same things. 1)
It depends where the reading is taken.
Oil coolers may not be needed in cooler climate. The engine is not only air cooled, it is also oil cooled. 2)
The oil circulation carries a lot of the internal engine heat away. Engines are built to run certain specs.
Operating temperature has an effect on the specs due to heat expansion of the metal.
Minor point maybe, but the engines are not built to different specs to be sold in different climates.
We run different oil weights for different climates. The closer you stay to the ideal operating temp, the easier it will be on the engine.
It will also slow the oil breakdown.
People argue either way on the benefit of an oil cooler. 3) However, the reasoning for using an cooler ranges from:
Larger oil capacity, lower oil temp and better engine cooling in summer (especially in high temp climates).
You will have to make your own decision on when to use an oil cooler.
Sometimes it just boils down to piece of mind.
But using one can't hurt the engine.
Here is some verbiage from an old Lockhart oil cooler advertisement:
Your bike works hard to conquer retarded ignitions, low octane fuel, heavy loads and stop and go traffic.
Under these conditions, the oil gets hot fast so that each 20° above 200F cuts your oil's usefulness in half.
(An oil cooler) will prolong tune-up periods, reduce engine wear and get you some peace of mind.
*———-Click Here to reference different PDF “Instruction” documents for oil cooler installations as offered by the MoCo over time.
All oil coolers and lines are plumbed in the part of the oil flow loop that returns engine oil to the oil tank.
Do not pull hoses too tight or oil flow restrictions can occur.
Some oil coolers have a built in thermostat to divert cooler oil from going thru the oil cooler.
However, external thermostat bypass valves were sold for Sportsters starting in 1979: Chrome (26248-78) and Black (26251-78).
Below are thermostat valves sold for 79-up Sportsters (also used on FX models, maybe others).
11) 12)
*———-Click Here to reference hose connections for Ironhead Sportsters using an oil cooler.
Scroll further down that page for Converting 57-78 Models to an Ext Oil Filter and Oil Cooler
Hoses must be routed so they do not contact or interfere with any hot or moving parts.
Hoses must be routed above the bottom of the frame tube to prevent hose damage if the frame should contact the pavement or a highway obstacle.
Photos by IronMick of the XLFORUM 16)
Note: If you ever want to remove the solenoid you are somewhat screwed
You cannot get at those two little 1/4“ bolts because the lines are in the way.
And you must use a socket as there is not enough space between the bolt head and the sol to fit a wrench.
It is possible to get it out thru the hole in the bottom of the battery box, but it is much quicker to remove the battery box completely.
Which involves removing a whole inventory of parts.
Here's the lines running to the oil cooler.
Note: if you have a “Custom” or forward controls you will need to remove the right side to gain access to the oil hose from the pump: 17)
Disconnect the feed hose from the oil pump to the engine.
Thread the included nipples (with thread sealer) into the pump and the case.
Install the (2) short metal lines to the fittings on the right side of the bike (18mm short wrench).
(it would be a good idea to install the plastic stand off's per the instructions)
Next, extend the metal lines with rubber hose to the cooler on the left side of the bike.
Use the clamps to mount the cooler unit to the downtube.
Jagg has several oil coolers to choose from including a chrome version, slimline, a deluxe with diamond cut fins and a wideline cooler.
They also offer a fan assisted cooler.
(perimeter, vertical frame tubes)
Jagg Slimline Oil Cooler:
19) 20) 21)
Jagg Slimline oil cooler installed 22) | |
Jagg's thermostatically-controlled offset oil filter adapter provides an easy access point to the bike's oil supply for the installation of the oil cooler. 23)
The offset filter adapter (4700) may hit the motor mount when mounted with the fittings down.
It may have to be mounted so the fittings are up to install the filter.
In this instance, the anti-rotation device is not required.
Note for 04 and up Sportsters:
Fittings mounted down wouldn't work 25) |
Jagg oil cooler with filter adapter 26) | |